Service bulletin 15NA067
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10250040 |
| Published by NHTSA | 2024-02-12 |
| Manufacturer's number | 15NA067 |
| Manufacturer's date | 2015-11-24 |
| NHTSA component | FUEL SYSTEM, DIESEL:DELIVERY:FUEL PUMP |
NHTSA's summary
Information on Ordering New Delphi Style Fuel Pump
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Fuel system, Fuel pump
| CHEVROLET SILVERADO 2500 | 2016 (the catalog's model; the bulletin names a series or trim of it) |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 15NA067 | 2023-12-11. Service bulletin. Information on Ordering New Delphi Style Fuel Pump |
|---|---|
| 18NA235 | 2022-05-31. Service bulletin. This information bulletin advised the tech of possible use of low fuel quality and the possible ramifications in performance in regards to the customers concerns. |
| PIE0523 | 2019-07-01. Service bulletin. This engineering informational bulletin is requesting information for vehicles that has had the fuel injection pump replaced and is still within warranty. |
| PIP5596 | 2018-11-13. Service bulletin. This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation. |
| 15-NA-067 | 2018-05-21. Service bulletin. This informational bulletin provides information for dealership personnel and technicians that when replacing the fuel pump, the vehicle should be serviced with the same style high pressure fuel pipe and SIDI fuel pump it was equipped with. |
| 17NA335 | 2018-04-23. Service bulletin. This technical bulletin provides a procedure to replace the fuel pump to correct the MIL concerns. |
| PIP5411F | 2017-11-14. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that may have hesitation or a stalling condition while in ambient temperatures 100 degrees or higher. Technician may find Diagnostic Trouble Codes P2635 and or P018B set. The dealer is advised to replace the in tank fuel pump module assembly to correct the condition. |
| PIP5507B | 2017-08-15. Service bulletin. This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern. |
| PIP5507A | 2017-08-15. Service bulletin. This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern. |
| PIT5510B | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician how to diagnose and repair vehicles that may have fuel gauge that shows empty and the low fuel level indicator is on. Technician will find Diagnostic Trouble Code P2636 will be set in the Engine Control Module. Technician will need to install (Y) Fuel Tank Fill Vent hose. Technician will need to remove the original fuel balance pump line from the pump tube. Technician can now add a new line from the (Y) to the fuel balance pump line and reprogram the ECM with updated calibrations. If the vehicle returns with the same concern and Diagnostic Trouble Code P2636 set in the Engine Control Module. Technician will need to reprogram the Engine Control Module with the latest calibrations. |