Service bulletin 9100265
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10248845 |
| Published by NHTSA | 2024-01-16 |
| Manufacturer's number | 9100265 |
| Manufacturer's date | 2023-11-08 |
| NHTSA component | ENGINE AND ENGINE COOLING |
NHTSA's summary
Hydraulic tensioner Before replacing any Front End Accessory Drive components, please check Accessory Drive belt routing as per engine sales code. Customer complaints may include a noise coming from under de hood described as a squeal, screech, squeak, chirp or "belt related" noise and/or noisy tensioner/pulley. Please check Service Library for any STAR Online publications that may apply. Note: If it is found that the pulleys and/or tensioners are to blame for the noise please use an stethoscope or similar tool to determine the origin of the noise and include it in the narrative.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Engine
| CHRYSLER PACIFICA | 2022, 2023 |
|---|---|
| CHRYSLER VOYAGER | 2022, 2023 |
| DODGE DURANGO | 2022 |
| DODGE DURANGO1 | 2023 (the catalog's model; the bulletin names a series or trim of it) |
| JEEP GLADIATOR | 2022, 2023 |
| JEEP GRAND WAGONEER | 2023 |
| JEEP WAGONEER | 2022, 2023 |
| JEEP WRANGLER | 2022, 2023 |
| RAM 1500 | 2022, 2023, 2024 |
| RAM PROMASTER | 2023 |
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 22V865000 | 2022-11-23. ENGINE |
|---|---|
| 2022584 | 2022-10-14. Engine |
| 22V767000 | 2022-10-13. ENGINE; FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP |
A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.
| 18-015-26 REV. A | 2026-10-16. Service bulletin. Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0300-00 - Multiple Cylinder Misfire - in Active or Stored status set during cold start catalyst heating. ● P0301-00 - Cylinder 1 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0302-00 - Cylinder 2 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0303-00 - Cylinder 3 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0304-00 - Cylinder 4 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0305-00 - Cylinder 5 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0306-00 - Cylinder 6 Misfire - in Active or Stored status set during cold start catalyst heating. Customers may also comment on one or more of the following: ● Vehicle has a rough idle. ● Engine has a miss. ● Noisy valvetrain. This bulletin involves inspecting the vehicle and, if required, reprogramming the PCM with the latest available software. |
|---|---|
| 18-015-26 REV. A | 2026-10-16. Service bulletin. Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0300-00 - Multiple Cylinder Misfire - in Active or Stored status set during cold start catalyst heating. ● P0301-00 - Cylinder 1 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0302-00 - Cylinder 2 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0303-00 - Cylinder 3 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0304-00 - Cylinder 4 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0305-00 - Cylinder 5 Misfire - in Active or Stored status set during cold start catalyst heating. ● P0306-00 - Cylinder 6 Misfire - in Active or Stored status set during cold start catalyst heating. Customers may also comment on one or more of the following: ● Vehicle has a rough idle. ● Engine has a miss. ● Noisy valvetrain. This bulletin involves inspecting the vehicle and, if required, reprogramming the PCM with the latest available software. |
| S2609000006 REV.A | 2026-10-07. Service bulletin. Customer indicates Malfunction Indicator Light (MIL) or Check Engine Light (CEL) coming on. |
| S2609000011 | 2026-09-17. Service bulletin. MIL-On and/or Engine Oil Leak |
| 9100898 | 2026-09-17. Service bulletin. Engine PNs: MY 24-26 WD/DT (5.7L) Code P00B is being misdiagnosed and incorrect parts are being installed causing over repair. Refer to SOL S2609000006 The IAFM Foam Engine Valley Cover (PN 53013735AB) does not provide sufficient clearance for proper routing of the MDS solenoid jumper harness (PN 05148163AE). As a result, the harness may become compressed by the foam cover. To prevent unnecessary part replacement, the MDS solenoid jumper harness (PN 05148163AE) should be inspected for damage or pinch conditions prior to replacing the following part numbers: Engine PNs: 68409343AA 68409357AA 68450915AA OCV PNs: 53022338AB Phaser PNs: 53022298AA 53022298AB |
| 9100363 Rev 3 | 2026-09-03. Service bulletin. Turbocharger Kit Please note that many turbo components are serviceable separately and full turbo replacement may not be required. If the turbo is being inspected for: Noise/Rattle: Inspect heat shield fasteners for looseness and check the wastegate actuator/linkage for binding. The actuator kit is serviced separately. Oil Leak: Inspect the turbo oil feed O-ring area for leaks. O-ring is serviced separately. |
| 113803 | 2026-08-13. Service bulletin. HOSE AND TUBE - HEATER SUPPLY AND RETURN |
| 9100861 Rev 3 | 2026-08-06. Service bulletin. PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Inspect battery terminals for damage to rule out a battery drainage issue. 6) Ensure the PCM is up-to-date with the latest available flash. If correct repair is not performed then the claim or condition will be recovered by Warranty Operations. |
| 9100861 Rev 1 | 2026-07-23. Service bulletin. PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Inspect battery terminals for damage to rule out a battery drainage issue. 6) Ensure the PCM is up-to-date with the latest available flash. |
| 113280 | 2026-07-18. Service bulletin. HOSE AND TUBE - EGR COOLANT |