WenmarOpen by Wenmar Pro

Service bulletin 1900323

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10243269
Published by NHTSA2023-10-02
Manufacturer's number1900323
Manufacturer's date2023-08-24
NHTSA componentSTEERING

NHTSA's summary

Steering Wheel Off-Center Customers may experience the steering wheel is off-center. This bulletin involves re-centering the steering wheel.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Steering

Vehicles listed
JEEP COMMANDER2023 to 2024
JEEP COMPASS2022, 2023, 2024
JEEP RENEGADE2022, 2023
JEEP RENEGADE2024

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
19-004-262026-09-03. Service bulletin. Not applicable to vehicles built for US market. Tingling/Vibration When Turning The Steering Wheel Customers may experience the following: SYMPTOM: ● Tingling sensation or vibration felt when holding the steering in a turned (off center) position.
1134502026-07-23. Service bulletin. CLOCKSPRING - STEERING COLUMN CONTROL MODULE
1134492026-07-23. Service bulletin. CLOCKSPRING - STEERING COLUMN CONTROL MODULE
S26230000432026-06-16. Service bulletin. POWER STEERING SYSTEM HOT - PERFORMANCE MAY BE LIMITED Message And Or C2210-00 EPS ECU Overtemperature.
1072152025-10-02. Service bulletin. CLOCKSPRING - STEERING COLUMN CONTROL MODULE
1073492025-10-02. Service bulletin. CLOCKSPRING - STEERING COLUMN CONTROL MODULE
08-251-24 REV. A2024-12-18. Service bulletin. "Noise From Steering Wheel While Turning Customers may comment on the following: ● Noise when turning the steering wheel. This bulletin involves inspecting the steering wheel operation for a noise while turning and, if noisy, repositioning the steering wheel wire harness."
08-251-242024-12-17. Service bulletin. "Noise From Steering Wheel While Turning Customers may comment on the following: ● Noise when turning the steering wheel. This bulletin involves inspecting the steering wheel operation for a noise while turning and, if noisy, repositioning the steering wheel wire harness."
91004392024-10-31. Service bulletin. MODULE Steering Control Before replacing the steering column control module (SCCM) due to front or rear windshield wiper operation / blindspot inop / lane assistant inop/ DTC B178F-15 active, please follow these steps: 1.- Refer to TSB-08-219-24 MP - Rear Windshield Wipers Operate Continuously and TSB 08-136-24 REV. A - Adaptive Cruise Control (ACC) Module Update. 2.- Verify if failure is still present (review wipers, turn signal, blindspot and lane assistant status) and if DTCs still active. 3.- If failure still present, make sure all the switches' and airbag's harness are properly connected and there is no corrosion, disconnect the switches & reconnect them, and reverify the issue. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from wipers is requested, if turn signal, blindspot and lane assistant work. 5.- Do a hard reset of battery to BCM and evaluate if any DTC is set. Retest if failure still present. If there are no DTC's, physical defects, wipers inop, nor turn signal inop, then SCCM does not need to be replaced.
91003612024-07-08. Service bulletin. CLOCKSPRING Steering Column Control Module Before replacing the steering column control module (SCCM), please follow these steps: 1.- Make sure all the switches' and airbag's harness are properly connected, disconnect the switches and reconnect them, and reverify the issue. 2.- Pull the SCCM fuse for 60 sec and then reinstall it. 3.- Reverify if Steering wheel switches are inoperative. If there are no DTC's, physical defects, nor switches inop, then SCCM does not need to be replaced.