WenmarOpen by Wenmar Pro

Service bulletin 23-01-037G

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10235568
Published by NHTSA2023-05-04
Manufacturer's number23-01-037G
Manufacturer's date2023-04-25
NHTSA componentENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; FUEL SYSTEM, GASOLINE

NHTSA's summary

Certain 2017-2020MY G80 vehicles may exceed evaporative emissions standards due to Onboarding Refueling Vapor Recovery (ORVR) system. To correct this symptom, install an auxiliary canister assembly between the canister and Canister Close Valve (CCV).

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Engine, Exhaust and emissions, Fuel system

Vehicles listed
GENESIS G802017, 2018, 2019, 2020

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
20241582024-03-08. Engine
24V1910002024-03-08. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER
19V5380002019-07-19. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER
20193502019-07-17. Engine

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
21-FL-003G2024-04-11. Service bulletin. This TSB provides consolidated diagnosis and repair information, currently in the shop manual, to address DTC U0109 / U010900 related to a communication error with the Fuel Pump Control Module (FPCM).
21-01-020G2024-04-11. Service bulletin. This bulletin provides information related to the ECM(Engine Control Module) software update for G80/G90 with 5.0L GDI engine equipped vehicles. This updates the software logic dealing with OBD communication test.
18-01-006-G2024-04-11. Service bulletin. This bulletin provides information related to an ECM (Engine Control Module) software update for OBD (On Board Diagnostics) logic improvement. The Fuel System Readiness settings logic has been updated.
23-01-037HG2023-07-01. Service bulletin. Certain 2017-2020MY G80 vehicles may exceed evaporative emissions standards due to Onboard Refueling Vapor Recovery (ORVR) system. To correct this symptom, install an auxiliary canister assembly between the canister and Canister Close Valve (CCV).
23-01-037HG2023-07-01. Service bulletin. Certain 17-18MY Genesis G80 (DH) vehicles may exceed evaporative emissions standards due to Onboard Refueling Vapor Recovery (ORVR) system. To correct this symptom, an auxiliary canister assembly between the canister and Canister Close Valve (CCV) will be installed.
23-01-037G2023-05-04. Service bulletin. Certain 2017-2020MY G80 vehicles may exceed evaporative emissions standards due to Onboard Refueling Vapor Recovery (ORVR) system. To correct this symptom, install an auxiliary canister assembly between the canister and Canister Close Valve (CCV).
23-AT-001G2023-04-04. Service bulletin. When servicing a vehicle with a “Check Engine light” and any of the DTCs listed below, follow the Service Procedure to replace the related solenoid and E-module or park position switch.
21-FL-003HG2021-08-07. Service bulletin. This TSB provides consolidated diagnosis and repair information, currently in the shop manual, to address DTC U0109 / U010900 related to a communication error with the Fuel Pump Control Module (FPCM).
21-EM-006HG(1)2021-05-05. Service bulletin. Certain G80 and G90 Genesis vehicles may experience DTC code P0597 for “Thermostat Heater Control Circuit/Open”. This bulletin provides information on replacing the electric thermostat. No drivability issues are associated with this condition.
21-EM-004H2021-04-07. Service bulletin. This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.