Service bulletin 09-010-23

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10232282
Published by NHTSA	2023-03-03
Manufacturer's number	09-010-23
Manufacturer's date	2023-02-09
NHTSA component	VISIBILITY; BACK OVER PREVENTION; VISIBILITY:POWER WINDOW DEVICES AND CONTROLS; UNKNOWN OR OTHER

NHTSA's summary

Some vehicles may exhibit a condition where the power outer mirror will not fold in and/or out when the outer mirror holding switch (1) is operated. This may be caused by: 1. The electric fold-in unit inside the outer mirror may be damaged by corrosion from water entry due to insufficient water tightness. 2. The electric fold-in unit may interfere with the outer mirror frame due to improper installation of the electric fold-in unit. 3. The friction around the shaft of the folding mechanism may increase.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Driver assistance, Glass, wipers and mirrors, Backup camera, Power windows

Vehicles listed
MAZDA MAZDA6	2019, 2020

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
SA-039-23a	2023-10-05. Service bulletin. Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
SA-001/22	2022-02-04. Service bulletin. Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. 6 Bluetooth device will not pair No. 7 Incorrect GPS position No. 8 Voice Recognition Does Not Work No. 9 Cannot Make a Hands-Free Call No. 10 Cannot Play Bluetooth Audio No. 11 Other Symptoms No. 12 How to update the Navigation SD Card Map No. 13 How to Check Navi SD Card VIN Lock
SA-040-21	2021-07-01. Service bulletin. Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
MT-003-21	2021-06-29. Service bulletin. Some vehicles may experience exterior trim heat damage when parked near a glass building. This may be caused by the suns reflection. If a building creates enough of a curve with a series of flat windows, which act like mirrors, the reflections all converge at one point, focusing and concentrating the light onto the street below.
15-004-19-3639	2019-10-04. Service bulletin. Some customer's may complain that In heavy rain, the front parking sensor system detects objects despite nothing being in front of the vehicle, and no related DTCs are stored. This may be caused by the ultrasonics diffusing inside when the front parking sensors get wet. As a result, the parking assist unit mistakenly detects objects near the front of the vehicle. To correct this issue, the detecting logic in close range has been improved.
09-033-19-3590	2019-08-21. Service bulletin. Some vehicles may exhibit the rear parking sensor beeping without any obstacles behind it when the shift lever is shifted into Reverse. This concern only occurs when the rear USB power outlet (1) is broken. This is caused by noise from USB interference with the harness of the rear parking sensor (when the USB power outlet is broken).To correct this issue, the configuration of the USB power outlet has been changed to improve durability.
SA-018-19	2019-05-30. Service bulletin. Due to a changes in the 2018 Mazda6, there are two things to note of when installing the Rear Parking Sensors. 1. When securing the main harness in step 4, DO NOT attach the one tie wrap as shown. There is the possibility of attaching it to the moonroof drain hose and pinching the hose. 2. When routing the sensor harness behind the rear bumper (section 8, Installation of Harness section 2-2) utilizing the 3 mount base positions, the middle mounting base position #2 is located under the Blind Spot Monitoring sensor bracket as shown.