Service bulletin 2101114
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10229856 |
| Published by NHTSA | 2023-01-17 |
| Manufacturer's number | 2101114 |
| Manufacturer's date | 2014-04-04 |
| NHTSA component | VEHICLE SPEED CONTROL:THROTTLE:ACTUATOR/STEPPER MOTOR |
NHTSA's summary
Improved Medium to Heavy Throttle Downshift Response
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Throttle and cruise control
| RAM 1500 | 2014 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 18V332000 | 2018-05-17. ELECTRICAL SYSTEM:SOFTWARE; VEHICLE SPEED CONTROL:CRUISE CONTROL; ELECTRICAL SYSTEM:WIRING |
|---|
A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.
| S1623000028 Rev. | 2023-02-13. Service bulletin. Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position. |
|---|---|
| 2302314 | 2022-09-26. Service bulletin. Metallic Rattle Noise From The Roof Headliner Area This bulletin involves bonding the roof sheet metal to the roof bow using urethane adhesive. Loud metallic rattle noise coming from the roof headliner area while driving over rough road surfaces and/or upon door closing. |
| S2008000081 Rev. | 2021-03-01. Service bulletin. Cruise Control Inoperative. |
| S1508000480 | 2020-05-26. Service bulletin. Speed Control Operates Intermittently |
| S1508000480 | 2020-05-18. Service bulletin. Speed Control Operates Intermittently |
| 56046094A | 2018-11-26. Service bulletin. Cruise Control Switch Before ordering or replacing this part please contact Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair. |
| 20614 | 2018-06-11. Service bulletin. P/N 68111384AB: Inspect &Return: Switch - Speed Control You have been identified as either having stock, or have stock in transit to your dealership. Please return parts which have a pacakging date code of July 20th 2016. Reference pictures attached for suspect part identification. Please return parts backto your facing depot using Return Code 02, before 31 August, 2016. |
| 68277402A | 2018-06-11. Service bulletin. Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure |