Service bulletin 2302516
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10226277 |
| Published by NHTSA | 2022-11-21 |
| Manufacturer's number | 2302516 |
| Manufacturer's date | 2016-06-09 |
| NHTSA component | STRUCTURE:BODY:DOOR |
NHTSA's summary
Discolored Door Hinge Nuts This bulletin involves replacing all the lower nuts on the side upper and lower door hinges. The customer may describe discoloring or rust from the lower nut securing the doors to the hinges.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Body and frame
| JEEP WRANGLER | 2015, 2016 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 100192 | 2024-10-02. Service bulletin. BOW - FOLDING TOP |
|---|---|
| S1723000037 REV.A | 2024-06-11. Service bulletin. Freedom Panel Underside Rough And Or White Coating Flaking |
| 2302714 | 2023-01-17. Service bulletin. Zinc Coating Missing From Left Rear Close Out Panel |
| 2303614 | 2023-01-17. Service bulletin. Water Leak At Hard Top Rear Seam This bulletin involves replacing the hard top. . The customer may describe water dripping from the top, running down the inside of the back glass, or running down the inside rear D-pillar. |
| 9003182 | 2023-01-17. Service bulletin. Part Description: Hard Top Flipper Glass Prop Rod Issue Description: Having a light oil sheen on the steel shaft of the prop rod is correct and acceptable. Please do not replace the Prop Rod for this condition. |
| 3100122 | 2023-01-09. Service bulletin. Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components. |
| 2300415 | 2023-01-09. Service bulletin. Side Steps Are Missing This bulletin involves inspecting for and if necessary installing the Side Steps. Side Steps are missing. Inspect for and if necessary install the Side Steps. |
| 3100122 | 2022-10-31. Service bulletin. Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components. |
| 3100122 | 2022-10-31. Service bulletin. Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components. |
| 9003665 | 2022-10-31. Service bulletin. Fuel Tank and Fuel Evap System Components 1) For JK MIL On ? P0441: Before replacing this part due to fault code P0441, check for restriction due to plastic over-flash in the Purge Hose Port of the Intake Manifold. If there is flash in the Purge Hose Port of the Intake Manifold and the vehicle is 2016 MY then replace the Intake Manifold and send to QEC. Otherwise, remove the flash with a 5/32? drill bit and clean the Intake Manifold of any flash debris. If the fault code P0441 continues after repairing the Intake Manifold, then send Freeze Frame data of P0441 to Michael.Ade@FCAgroup.com and contact Sylvia Lopez at cell number (248) 520-9734. If you don`t receive response within 15 minutes, please continue with the normal repair procedure. 2) For RT MIL On ? P0456: If ESIM needs to be replaced for fault code P0456, check the Vapor Line, Fresh Air Filter and the Black Frame Rail Blocker for water ingestion. If water ingestion is found, then replace the ESIM part number 04861962AB and the Jumper, Vent Recirculation Tube part number 04721757AI. Please contact Release Engineer Alfredo Salituro @ 213-700-5359 before performing repair service. If you do not receive a response within 15 minutes, please continue with the normal repair procedure. |