Service bulletin 9003803
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10224892 |
| Published by NHTSA | 2022-10-31 |
| Manufacturer's number | 9003803 |
| Manufacturer's date | 2017-10-18 |
| NHTSA component | BACK OVER PREVENTION |
NHTSA's summary
Ambient Temperature Sensor If replacing an ambient temperature sensor on 2017 JC (Journey) for P0070, P0071, P0072, or P0073 fault codes, please call Omar Jobe at cell (248) 910-2166. If you do not receive a response within 15 minutes, please proceed with repair. Digital images of any physical issue discovered would be very helpful. Please send digital images to email address: omar.jobe@fcagroup.com.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Driver assistance, Backup camera
Trouble codes named
P0070, P0071, P0072, P0073
| DODGE JOURNEY | 2017 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 9003357 | 2024-01-02. Service bulletin. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA. |
|---|---|
| 9003059 | 2022-08-08. Service bulletin. Park Assist Sensor 1) Active or Stored DTC of Signal Shape / Waveform Failure fault: B128E-25, B128F-25, B1290-25, B1291-25, B1292-25, B1293-25, B1295-25, B1296-25, B1297-25, and/or B1298-25, check for snow/mud/ice/obstruction and clean the Sensors, both front and back (behind bumper) of sensor. The snow/mud/ice can be behind the bumper, sensor retainer and/or the sensor which may cause customers to think they have an issue since they cleaned the front of the sensor/bumper, but not behind where dirt/mud/ice snow can accumulate. Once the Bumper and Sensors are completely cleaned and clear of snow, mud, ice, and/or obstruction, the sensors must activate in order for the faults to go STORED. After cleaning the Bumper and Sensors, turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED. 2) Active or Stored DTC code of Short to Ground fault: B128E-11, B128F-11, B1290-11, B1291-11, B1292-11, B1293-11, B1294-11, B1295-11, B1296-11, and/or B1298-11, or if you have an active or stored DTC code of Performance or Incorrect Operation fault: B128E-92, B128F-92, B1290-92, B1291-92, B1293-92, B1294-92, B1295-92, B1296-92, B1297-92, and/or B1298-92, then check the wiring behind the sensor. Specifically, ensure that the connector behind the park assist sensor is fully mounted. Ensure also, there is no dirt, corrosion, or damage in this connector behind the park assist sensor as this will also cause a Short to Ground fault. With potential wiring issues addressed, the sensors must activate in order for the faults to go STORED. After all sensors are properly connected (you will likely hear a click once the connector is fully seated on the sensor), turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED. |