Service bulletin S2108000123

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10223285
Published by NHTSA	2022-10-17
Manufacturer's number	S2108000123
Manufacturer's date	2021-05-22
NHTSA component	ENGINE

NHTSA's summary

Stored U0080-00 DTC Code Ethernet Bus 1 Fault Set By SGW

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Engine

Trouble codes named

U0080

Vehicles listed
JEEP GRAND CHEROKEE	2021
JEEP GRAND WAGONEER	2022

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
2022217	2022-04-28. Engine
22V284000	2022-04-28. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE)

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
9100861 Rev 3	2026-08-06. Service bulletin. PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Inspect battery terminals for damage to rule out a battery drainage issue. 6) Ensure the PCM is up-to-date with the latest available flash. If correct repair is not performed then the claim or condition will be recovered by Warranty Operations.
9100861 Rev 1	2026-07-23. Service bulletin. PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Inspect battery terminals for damage to rule out a battery drainage issue. 6) Ensure the PCM is up-to-date with the latest available flash.
9100861	2026-07-18. Service bulletin. PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Ensure the PCM is up-to-date with the latest available flash. 6) Inspect battery terminals for damage to rule out a battery drainage issue.
112639	2026-07-08. Service bulletin. THROTTLE BODY – NONE
112640	2026-07-08. Service bulletin. THROTTLE BODY – NONE
112842	2026-07-02. Service bulletin. BOLT - HEX FLANGE HEAD
9100832	2026-06-18. Service bulletin. Before replacing the starter, please follow the published diagnostics in the Service Information at 08 - Electrical / 8F - Engine Systems / Starting / Diagnosis and Testing / STANDARD STARTING SYSTEM. Updates to this procedure have been recently made and should be followed.
18-050-26	2026-04-22. Service bulletin. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0300 - Multiple Cylinder Misfire - In Active or Stored status set during cold start catalyst heating. ● P0301 - Cylinder 1 Misfire - In Active or Stored status set during cold start catalyst heating. ● P0302 - Cylinder 2 Misfire - In Active or Stored status set during cold start catalyst heating. ● P0303 - Cylinder 3 Misfire - In Active or Stored status set during cold start catalyst heating. ● P0304 - Cylinder 4 Misfire - In Active or Stored status set during cold start catalyst heating. ● P0305 - Cylinder 5 Misfire - In Active or Stored status set during cold start catalyst heating. ● P0306 - Cylinder 6 Misfire - In Active or Stored status set during cold start catalyst heating. Customers may also comment on one or more of the following: ● Check engine illuminates when fueling the vehicle while the engine is running. ● Vehicle has a noticeable misfire. ● Vehicle idles rough. ● Engine noise. NOTE: Noise is heard coming from the valvetrain. In addition, the following software enhancement is available: ● Update to prevent customers from driving their vehicles while the Electric Park Brake (EPB) is engaged. Engine torque will be limited to prevent the Rear Drive Unit from being damaged. NOTE: Previously, the EPB would remain engaged without any torque limit which could lead to the Rear Drive Unit being damaged/broken. This bulletin involves reprogramming the PCM with the latest available software.
9100790	2026-04-01. Service bulletin. Before replacing the water pump on 3.0L SO/HO, please follow the updated WATER PUMP INSPECTION diagnostic procedure to confirm the leak persists "09 - Engine, 3.0L GMET6 / Cooling System / Engine Cooling / Diagnosis and Testing / COOLING SYSTEM LEAKS"
9100789	2026-04-01. Service bulletin. Before replacing the water pump on 3.0L SO/HO, please follow the updated WATER PUMP INSPECTION diagnostic procedure to confirm the leak persists "09 - Engine, 3.0L GMET6 / Cooling System / Engine Cooling / Diagnosis and Testing / COOLING SYSTEM LEAKS"