Service bulletin 2300922

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10220785
Published by NHTSA	2022-09-26
Manufacturer's number	2300922
Manufacturer's date	2022-03-09
NHTSA component	ENGINE AND ENGINE COOLING; VISIBILITY; FUEL SYSTEM, GASOLINE

NHTSA's summary

Side Mirror Clicking or Inoperative This bulletin involves trimming 75mm +/- 5mm (3 inches) of the lower lip of theside mirror?s cut line rubber seal. Customers may comment on the following:Audible clicking sound when retracting the side mirrors and/or inability to fold in the mirrors.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Engine, Fuel system, Glass, wipers and mirrors

Vehicles listed
JEEP GRAND WAGONEER	2022

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
2024338	2024-06-13. Visual System
2023456	2023-08-14. Visual System

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
9100861 Rev 3	2026-08-06. Service bulletin. PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Inspect battery terminals for damage to rule out a battery drainage issue. 6) Ensure the PCM is up-to-date with the latest available flash. If correct repair is not performed then the claim or condition will be recovered by Warranty Operations.
9100861 Rev 1	2026-07-23. Service bulletin. PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Inspect battery terminals for damage to rule out a battery drainage issue. 6) Ensure the PCM is up-to-date with the latest available flash.
9100861	2026-07-18. Service bulletin. PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Ensure the PCM is up-to-date with the latest available flash. 6) Inspect battery terminals for damage to rule out a battery drainage issue.
9100833 REV1	2026-07-18. Service bulletin. Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
9100833	2026-07-02. Service bulletin. Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
9100832	2026-06-18. Service bulletin. Before replacing the starter, please follow the published diagnostics in the Service Information at 08 - Electrical / 8F - Engine Systems / Starting / Diagnosis and Testing / STANDARD STARTING SYSTEM. Updates to this procedure have been recently made and should be followed.
9100838	2026-06-18. Service bulletin. Before replacing any parts check for applicable TSBs/RSUs. If no applicable TSBs/RSUs, or they have already been applied, please refer to the updated Service Library diagnostic procedure for P1CEA-00-BOOST SIDE EVAP PURGE SYSTEM PERFORMANCE (MODULE, Powertrain Control (PCM), 3.0L GMET6) and SOL S2518000008.
9100790	2026-04-01. Service bulletin. Before replacing the water pump on 3.0L SO/HO, please follow the updated WATER PUMP INSPECTION diagnostic procedure to confirm the leak persists "09 - Engine, 3.0L GMET6 / Cooling System / Engine Cooling / Diagnosis and Testing / COOLING SYSTEM LEAKS"
9100789	2026-04-01. Service bulletin. Before replacing the water pump on 3.0L SO/HO, please follow the updated WATER PUMP INSPECTION diagnostic procedure to confirm the leak persists "09 - Engine, 3.0L GMET6 / Cooling System / Engine Cooling / Diagnosis and Testing / COOLING SYSTEM LEAKS"
18-040-26	2026-03-25. Service bulletin. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1 (In Active or Stored status). ● P0071-00 - Ambient Air Temperature Sensor Performance (In Active or Stored status). ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low (In Active or Stored status). ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High (In Active or Stored status). ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or (In Active or Stored status). ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1 (In Active or Stored status). ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/stuck Off (In Active or Stored status). ● P05BD-00 - Stop-Start Mode Switch Range/Performance (In Active or Stored status). ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance (In Active or Stored status). ● P062B-00 - Internal Control Module Fuel Injector Control Performance (In Active or Stored status). ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/Performance (In Active or Stored status). ● P0604-00 - Internal Control Module Random Access Memory RAM Error (In Active or Stored status). ● P060C-00 - Internal Control Module Main Processor Performance (In Active or Stored status). ● U0104-00 - Lost Communication With Cruise Control Module (In Active or Stored status). Customers may also comment on the following: ● Oil Level High Warning in the Instrument Panel Cluster (IPC).** This bulletin involves reprogramming the PCM with the latest available software.