# Service bulletin 23\-024\-16

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 10218258
- Published by NHTSA: 2022\-08\-22
- Manufacturer's number: 23\-024\-16
- Manufacturer's date: 2016\-06\-03
- NHTSA component: VEHICLE SPEED CONTROL

## NHTSA's summary

Distorted Door Run Applique At Top Of Window This bulletin involves inspecting and if necessary, replacing the left front door glass run applique and window glass. The customer may describe that the left front door glass run applique has a wrinkled appearance or that the window does not fully close due to applique seal entrapment.

## The document

- [NHTSA's copy of the document (PDF)](https://static.nhtsa.gov/odi/tsbs/2016/MC-10218258-0001.pdf)
- [If that address does not open, try this one](https://static.nhtsa.gov/odi/tsbs/2016/MC-10218258-9999.pdf)

The document is the manufacturer's. This site does not hold it.

## Components

Throttle and cruise control

## Vehicles listed

- 2016 DODGE DART

## Other bulletins for the same vehicles and component

- [9003413](/bulletins/10219831.md), 2022-09-15, Service bulletin: VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
- [S1508000480](/bulletins/10175501.md), 2020-05-26, Service bulletin: VEHICLE SPEED CONTROL. Speed Control Operates Intermittently
- [S1508000480](/bulletins/10175088.md), 2020-05-18, Service bulletin: VEHICLE SPEED CONTROL. Speed Control Operates Intermittently
- [53034160A](/bulletins/10159998.md), 2019-05-20, Service bulletin: VEHICLE SPEED CONTROL; VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Part Description: Accelerator Pedal Issue Description: Vehicle has accelerator pedal fault code. Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
- [68277402A](/bulletins/10139956.md), 2018-06-11, Service bulletin: VEHICLE SPEED CONTROL:CRUISE CONTROL. Adaptive Cruise Control Sensor 1\) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.\~ 2\) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced \(TCM, PCM, ESP/ABS, etc\). This fault is not due to the ACC Sensor. No sensor replacement is required.\~ 3\) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage \(if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module\), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. \*\*Hints for running Horizontal Alignment procedure: A\) Verify speed is between 45 and 75 mph, B\) verify the road is relatively straight with signs, poles, guard rails, etc C\) Do not tail a vehicle too closely this inhibits the learning procedure
- [9003413](/bulletins/10138856.md), 2018-06-04, Service bulletin: VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

JSON: [/v1/bulletins/10218258](/v1/bulletins/10218258)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%2023-024-16&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F10218258&vehicle=Service%20bulletin%2023-024-16)