WenmarOpen by Wenmar Pro

Service bulletin 1802416REVA

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10218100
Published by NHTSA2022-08-22
Manufacturer's number1802416REVA
Manufacturer's date2016-04-01
NHTSA componentPOWER TRAIN

NHTSA's summary

Diagnostic And System Improvements.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Transmission and driveline

Vehicles listed
JEEP WRANGLER2010, 2011

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
12V2160002012-05-16. POWER TRAIN:AUTOMATIC TRANSMISSION
11V1450002011-03-01. POWER TRAIN:AXLE ASSEMBLY

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
1012322024-11-07. Service bulletin. Plate - Planetary
V512022-12-19. Service bulletin. Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
S1121000006RevA2022-09-26. Service bulletin. (Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
90040092022-09-26. Service bulletin. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
08100142022-09-26. Service bulletin. Loss Of Power Heated Mirror Function - Recall P61 Interim Repair This bulletin involves removing the M35 fuse.
S802022-09-15. Service bulletin. Customer Satisfaction Notification S80 Aftermarket Dana 60 Front Axle The aftermarket front axle steering knuckles have been machined with an incorrect taper during the manufacturing process on about 250 of the above vehicles, with approximately 80 of the axles sold by Mopar aftermarket. This condition can result in premature axle knuckle wear. The aftermarket front axle knuckles must be replaced with new axle knuckles for the left side and right side.
18024162022-08-22. Service bulletin. Diagnostic And System Improvements.
S1121000006 Rev.2020-09-28. Service bulletin. (Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
V512020-01-21. Service bulletin. Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
06-001-152018-11-26. Service bulletin. Squeak Noise While Depressing The Clutch Pedal This bulletin involves lubricating the clutch pedal return spring. Squeak noise from under the dash while depressing or releasing the clutch pedal.