# Service bulletin 9002688

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 10216418
- Published by NHTSA: 2022\-07\-25
- Manufacturer's number: 9002688
- Manufacturer's date: 2013\-02\-13
- NHTSA component: WHEELS; ENGINE AND ENGINE COOLING

## NHTSA's summary

68069384A$, R8069384A$, 68086182A$, R8027067A$, RL002012A$ \- Gasket, Cylinder Head Cover Before replacing injectors for Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, and/or P0206, please make sure that the wiring loom and/or connector in the valve cover gasket is not the root cause to your concern. In addition, make sure that the wiring attaching nuts are torqued to their proper value.\~

## The document

- [NHTSA's copy of the document (PDF)](https://static.nhtsa.gov/odi/tsbs/2013/MC-10216418-0001.pdf)
- [If that address does not open, try this one](https://static.nhtsa.gov/odi/tsbs/2013/MC-10216418-9999.pdf)

The document is the manufacturer's. This site does not hold it.

## Components

Engine, Wheels

## Trouble codes named

P0201, P0202, P0203, P0204, P0205, P0206

## Vehicles listed

- 2010 to 2012 DODGE RAM 1500
- 2010 to 2012 DODGE RAM 2500
- 2010 to 2012 DODGE RAM 3500
- 2011 to 2012 DODGE RAM 4500
- 2011 to 2012 DODGE RAM 5500
- 2009 RAM 1500
- 2009 RAM 2500
- 2007 to 2009 RAM 3500
- 2008 to 2009 RAM 4500
- 2008 to 2009 RAM 5500
- 2010 RAM redundant 4500
- 2010 RAM redundant 5500

## Recalls for the same vehicles and component

- [21V398000](/recalls/nhtsa/21V398000.md), 2021-05-27: WHEELS:LUGS/NUTS/BOLTS/STUDS
- [14V635000](/recalls/nhtsa/14V635000.md), 2014-10-08: ENGINE AND ENGINE COOLING:ENGINE:DIESEL; FUEL SYSTEM, DIESEL

## Other bulletins for the same vehicles and component

- [112906](/bulletins/11034373.md), 2026-07-02, Service bulletin: ENGINE. BEARING \- CRANKSHAFT THRUST and KIT
- [112906](/bulletins/11034337.md), 2026-07-02, Service bulletin: ENGINE. BEARING \- CRANKSHAFT THRUST and KIT
- [1804823](/bulletins/10236933.md), 2023-05-30, Service bulletin: EQUIPMENT; ENGINE AND ENGINE COOLING. wiTECH Small Leak Verification Test \(SLVT\) \- P0456\-EVAP SYSTEM SMALL LEAK
- [S2109000004](/bulletins/10230180.md), 2023-01-17, Service bulletin: ENGINE AND ENGINE COOLING. Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
- [9004374\-1](/bulletins/10229993.md), 2023-01-17, Service bulletin: WHEELS. NUT, Wheel Flange Wheel Nut Service Torque should be 175 N\-M.
- [9004374](/bulletins/10229988.md), 2023-01-17, Service bulletin: WHEELS. NUT, Wheel Flange Wheel Nut Service Torque should be 190 N\-M.
- [S2209000004](/bulletins/10227983.md), 2022-12-19, Service bulletin: EQUIPMENT; ENGINE AND ENGINE COOLING. If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
- [68332810](/bulletins/10223854.md), 2022-10-17, Service bulletin: ENGINE AND ENGINE COOLING. Service \- Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY \- The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T\-joints.\~ 2. Fill the T\-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar® Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2\-mm \[0.063\-in\] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.\~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket\(s\) onto the oil pan flange.\~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2\-mm \[0.063\-in\] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.\~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 N·m \[21 ft. lbs.\].
- [2303117](/bulletins/10223679.md), 2022-10-17, Service bulletin: WHEELS. Wheel Liner to Steel Bumper Slip Fit Design This bulletin involves informing technicians that the wheel liners tabs are to be tucked behind the flange of the bumper bracket. No fasteners are used to attach the liner and the bumper when vehicle is equipped with a steel front bumper.
- [9002887](/bulletins/10223599.md), 2022-10-17, Service bulletin: ENGINE AND ENGINE COOLING. Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.\~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.\~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

JSON: [/v1/bulletins/10216418](/v1/bulletins/10216418)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%209002688&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F10216418&vehicle=Service%20bulletin%209002688)