WenmarOpen by Wenmar Pro

Service bulletin PC863 2022 Front

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10207882
Published by NHTSA2022-02-10
Manufacturer's numberPC863 2022 Front
Manufacturer's date2022-01-19
NHTSA componentELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE; ENGINE AND ENGINE COOLING

NHTSA's summary

Engine Control Module (ECM) Reprogram Dealer Inventory *****Dealer Announcement***** Nissan is conducting a dealer inventory quality action to update the Engine Control Module (ECM) software on 4,251 specific MY2022 Nissan Frontier vehicles identified in Service Comm and National Service History – Open Campaigns. The ECM reprogram is intended to improve a possible cold startup mis-fire over thresh hold. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED INSPECTION INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History – Open Campaigns I.D. PC863 • New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). • Refer to NPSB 15-460 for additional information • Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this quality action. 3. Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 4. Once remedied, dealers should submit the applicable warranty claim for the action performed so it can be closed in Service Comm and release the vehicle for sale. ***** Dealer Responsibility ***** It is the dealer’s responsibility to check Service Comm or DBS National Service History – Open Campaign using the appropriate campaign ID for the inspection status on each affected vehicle currently in new vehicle inventory.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Electrical system, Engine, Engine control module

Vehicles listed
NISSAN FRONTIER2022

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
NTB24-0052024-02-08. Service bulletin. ENGINE RPM HIGHER THAN EXPECTED WHEN USING INTELLIGENT CRUISE CONTROL IF YOU CONFIRM The customer states the engine RPM is higher than expected after a downshift when using ICC. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Confirm the current ICC/ADAS 2 part number. 2. Reprogram the ICC/ADAS 2, if applicable. 3. Configure the ICC/ADAS 2. 4. Erase the DTCs.
NTB22-0262022-06-08. Service bulletin. SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire “Fuel Level Sensor Unit, Fuel Filter and Fuel Pump Assembly” (fuel pump assembly). The fuel level sensor can be replaced separately. • P0460 (FUEL LEV SEN SLOSH) • P0461 (FUEL LEVEL SENSOR) • P0462 (FUEL LEVL SEN/CIRC) • P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
NTB13-027C2022-03-12. Service bulletin. CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-0012022-02-10. Service bulletin. DTC P0300 AND/OR P0301(2/3/4/5/6) IS STORED DURING A COLD START IF YOU CONFIRM DTC P0300 and/or any of the following DTCs are stored in the ECM; • P0301 • P0302 • P0303 • P0304 • P0305 • P0306 AND The DTC only stores during a cold start. ACTION 1. Confirm the current ECM part number. 2. Reprogram the ECM, if applicable. 3. Replace the intake manifold.