Service bulletin 09-028-21-3748

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10201775
Published by NHTSA	2021-10-02
Manufacturer's number	09-028-21-3748
Manufacturer's date	2021-09-17
NHTSA component	STRUCTURE; EQUIPMENT

NHTSA's summary

Some customers may complain about a whistling noise heard from the top of the A-pillar area when driving at highway speeds. When driving under following conditions, a negative pressure is generated on the doors pulling them outward and resulting in weatherstrip vibration. The vehicle is exposed to a side wind while driving at highway speeds. The vehicle is exposed to a strong side wind while driving at a speed slightly higher than highway speed.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Body and frame, Equipment and accessories

Vehicles listed
MAZDA CX-5	2017, 2018, 2019, 2020, 2021

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
SA-031-26	2026-05-05. Service bulletin. DESCRIPTION Some vehicles may require the replacement of a damaged VIN plate or vehicle certification label. To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the B􀀀pillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory.
SA-021-26	2026-05-05. Service bulletin. This Service Alert supersedes the previously issued SAs and bulletin(s) listed below: The changes are noted below in red. SA-010/23 02/09/23 DESCRIPTION Some customers may experience one or more electrical malfunctions after a vehicle body repair. A newly painted fender stay (2) may be causing a poor front harness (1) ground connection. The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. NOTE: DO NOT paint ground point (3) attachment bolt (4) is seated. NEWLY INSTALLED FRONT FENDER STAY NOTE: CAUTION: If the bolt (4) contact area (3) is painted when the front fender stay (2) is newly replaced, it could cause a malfunction in the PCM. Before painting a newly replaced part, protect the bolt (4) contact area (3) with masking tape (5) as shown in the figure.
SA-039/25	2025-09-05. Service bulletin. Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search.
09-013-25	2025-04-01. Service bulletin. Some CX-5 and CX-30 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Water from a high pressure car washer and/or condensation may drip onto the switch connector and cause corrosion. To eliminate this concern, the PLG rear switch has been modified with a waterproof connector.
09-022-24b	2024-11-03. Service bulletin. Some customers may complain that the power liftgate (PLG) may open unintentionally while the vehicle is parked or stopped. Due to the shape of the 7th generation remote transmitter, the power liftgate button may be long pressed unintentionally in a pocket or a bag. To eliminate this concern, the keyless control specification has been modified. The button press time has been increased from 0.5 seconds to 1 second.
SA-058-24	2024-09-04. Service bulletin. Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
SA-056-24	2024-09-04. Service bulletin. Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
SA-050-24	2024-09-04. Service bulletin. Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.
09-022-24a	2024-08-02. Service bulletin. Some customers may complain that the power liftgate (PLG) may open unintentionally while the vehicle is parked or stopped. Due to the shape of the 7th generation remote transmitter, the power liftgate button may be long pressed unintentionally in a pocket or a bag. To eliminate this concern, the keyless control specification has been modified. The button press time has been increased from 0.5 seconds to 1 second.
SA-036-24	2024-06-04. Other. Some customers may complain about color discrepancies (brightness differences) of the image displayed on the screen when using the 360°view monitor. As this phenomenon is not a system failure, do not make any repairs or replace any parts. Explain the cause of this occurrence to the customer as follows: The 360°view monitor is a system that provides a complete picture of the vehicle surroundings by combining the pictures captured by 4 separate cameras. These cameras are installed in the front, rear, right and left sides of the vehicle. Each camera has a color adjustment function (white balance) that operates independently from each other, which can result in color discrepancy when the combined picture is displayed on the screen. This is especially true when one of the cameras captures more green objects than the remaining cameras.