WenmarOpen by Wenmar Pro

Service bulletin TSB_BOD302

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10200333
Published by NHTSA2021-08-13
Manufacturer's numberTSB_BOD302
Manufacturer's date2021-08-09
NHTSA componentSTRUCTURE

NHTSA's summary

TECHNICAL SERVICE BULLETIN: SERVICE ACTION: FRONT DOOR TRIM GRIP HANDLE INSPECTION AND REPAIR (SA483) - This bulletin provides information to inspect the two (2) (LHS & RHS) front door trim grip handles on some 2022MY Stinger (CK) vehicles produced from February 25, 2021 through June 17, 2021, which may have the grip handle detached from the inside door trim.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Body and frame

Vehicles listed
KIA STINGER2022

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
TSB_BOD3172023-07-05. Service bulletin. TECHNICAL SERVICE BULLETIN: HEADLINER NOSIE REDUCTION - This bulletin provides information to apply anti-noise tape to the headliner and assist handle brackets on some 2022MY Stinger (CK) vehicles produced from September 9, 2021 through present, equipped with a sunroof. The affected vehicles may exhibit an intermittent noise due to normal body flexing while driving on uneven roads.
TSB_BOD3142023-06-01. Service bulletin. TECHNICAL SERVICE BULLETIN: OVERHEAD CONSOLE SUNGLASS DOOR-LATCH REPAIR - This bulletin provides information to repair the overhead console lamp assembly and sunglass door latch on some 2012-2023MY model vehicles listed in the table below, which may encounter the sunglass case of the overhead console lamp not closing properly.
TSB_BOD3092022-11-02. Service bulletin. TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR FOR SUNROOF OPERATION - This bulletin provides information to replace the rear sled assembly in the sunroof (left and right side) on some 2018-2023MY Stinger (CK) vehicles produced from September 21, 2017 through January 28, 2022, which may exhibit separation of the rear sled assembly in the sunroof mechanism, resulting in an inoperative sunroof.
TSB_ELE2552022-07-02. Service bulletin. TECHNICAL SERVICE BULLETIN: DYNAMIC BENDING LIGHT DTC B232509/B232609 - MOISTURE ABSORBENT & BRACKET REPLACEMENT - This bulletin provides information to repair an inoperative Dynamic Bending Light (DBL) by replacing the moisture absorbent and bracket on some 2018-2022MY Stinger (CK) vehicles produced from October 11, 2017 through April 27, 2022, which may exhibit a MIL 'ON' with DTC B232509 or B232609 (active or pending). This may be due to an expanded moisture absorbent causing the bracket to interfere with the DBL module. New parts are available to address this condition (see chart below for details).
TSB_BOD302_R12022-03-31. Service bulletin. TECHNICAL SERVICE BULLETIN SERVICE ACTION: FRONT DOOR TRIM GRIP HANDLE REPAIR (SA483) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to repair the two (2) (LHS & RHS) front door trim grip handles on some 2022MY Stinger (CK) vehicles produced from February 25, 2021 through June 17, 2021, which may have the grip handle detached from the inside door trim.
TSB_BOD055_R12021-10-02. Service bulletin. TECHNICAL SERVICE BULLETIN: INFORMATION FOR HEADLAMP CONDENSATION AND MOISTURE - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.