# Service bulletin NTB15070

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 10192617
- Published by NHTSA: 2021\-05\-10
- Manufacturer's number: NTB15070
- Manufacturer's date: 2015\-08\-06
- NHTSA component: STRUCTURE

## NHTSA's summary

IF YOU CONFIRM An oil leak from the Adapter Case Oil Seal or the O\-ring \(see Figure 1\). ACTION NOTE: DO NOT replace the Transfer Case for a leak from the Adapter Case Oil Seal or the O\-ring. Reseal the Adapter Case with the seals listed in PARTS INFORMATION and shown in Figure 1. \* Please see this bulletin for further details.

## The document

- [NHTSA's copy of the document (PDF)](https://static.nhtsa.gov/odi/tsbs/2015/MC-10192617-0001.pdf)
- [If that address does not open, try this one](https://static.nhtsa.gov/odi/tsbs/2015/MC-10192617-9999.pdf)

The document is the manufacturer's. This site does not hold it.

## Components

Body and frame

## Vehicles listed

- 2008 to 2015 NISSAN ROGUE

## Recalls for the same vehicles and component

- [2016165](/recalls/tc/2016165.md), 2016-04-15: Structure
- [16V219000](/recalls/nhtsa/16V219000.md), 2016-04-15: STRUCTURE:BODY:HATCHBACK/LIFTGATE:SUPPORT DEVICE/STRUT
- [2015334](/recalls/tc/2015334.md), 2015-07-23: Structure

## Other bulletins for the same vehicles and component

- [NTB09\-131C](/bulletins/11031705.md), 2026-04-29, Service bulletin: STRUCTURE:BODY. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS \(Federal Motor Vehicle Safety Standards\) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” \(metal plate or vinyl label\) is attached to the instrument panel or body on the driver side at the base of the windshield \(see Figure 1\). · The “Certification Label” \(vinyl adhesive label\) is located on the lower area of the driver side B\-Pillar \(see Figure 1\).
- [NTB09\-131C](/bulletins/11031704.md), 2026-04-29, Service bulletin: STRUCTURE:BODY. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS \(Federal Motor Vehicle Safety Standards\) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” \(metal plate or vinyl label\) is attached to the instrument panel or body on the driver side at the base of the windshield \(see Figure 1\). · The “Certification Label” \(vinyl adhesive label\) is located on the lower area of the driver side B\-Pillar \(see Figure 1\).
- [NTB13\-028H](/bulletins/10232658.md), 2023-03-07, Service bulletin: VISIBILITY; STRUCTURE. REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- [NTB09\-081J](/bulletins/10232656.md), 2023-03-07, Service bulletin: VISIBILITY; STRUCTURE. WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- [NTB10\-117A](/bulletins/10200011.md), 2021-08-06, Service bulletin: STRUCTURE; EQUIPMENT. VOLUNTARY SERVICE CAMPAIGN 2008 \- 2009 ROGUE; FRONT DOOR EXTERIOR HANDLE Service Campaign ID \# P0376 is no longer active. • Repair orders opened after this bulletin’s published date are no longer eligible for reimbursement under Campaign ID \# P0376. • Discard all previous versions of NTB10\-117.
- [NTB15062A](/bulletins/10192656.md), 2021-05-10, Service bulletin: STRUCTURE; BACK OVER PREVENTION; EQUIPMENT; SUSPENSION; ELECTRICAL SYSTEM. IF YOU CONFIRM There is a popping noise from either the right or the left front coil springs when turning to the right or left. NOTE: Electronic chassis ears may be helpful in isolating this type of noise. ACTION Replace both front coil springs, strut mount bearings, and all other parts listed under PARTS INFORMATION. Position the coil springs as shown on pages 2\-5. Check the front end alignment, adjust to factory specifications as needed. NOTE: Refer to the Electronic Service Manual \(ESM\), section FSU Front Suspension, for strut coil spring removal, installation, and alignment information. IMPORTANT: The Coil Spring Installation Guidelines section in this bulletin MUST be followed in order for a correct repair to be performed.
- [NTB14105](/bulletins/10192469.md), 2021-05-10, Service bulletin: STRUCTURE. IF YOU CONFIRM: The carpet is wet on the driver and/or front passenger floor \(see Figure 1\). \- A "sloshing" type noise may be heard while driving AND the source of the wetness is not caused by the air conditioning system. ACTION: 1. Determine if the leak is from the kick panel and/or cowl end area. 2. If confirmed, apply body sealant to the incident areas as outlined in this bulletin. See this bulletin for further detail.
- [PC315](/bulletins/10192429.md), 2021-05-10, Service bulletin: EQUIPMENT; STRUCTURE:BODY:HATCHBACK/LIFTGATE:HINGE AND ATTACHMENTS. Nissan is conducting a dealer service action of the rear lift gate hinge mounting bolt torque on 1,372 specific 2014 Rogue vehicles identified in SERVICE COMM.
- [NTB14047](/bulletins/10192373.md), 2021-05-10, Service bulletin: ELECTRICAL SYSTEM; STRUCTURE. IF YOU CONFIRM: The "front door power window and door lock/unlock switch \(RH\) finisher" \(switch finisher\) has a loose fit, causting an excessive gap. See Figure 1. ACTION: 1. Remove the passenger front door finisher \(door finisher\). \- Refer to the Electronic Service Manual \(ESM\), section INT\-Interior, for removal procedure. 2. Install a foam block where shown in SERVICE PROCEDURE. \- Use the foam block listed in PARTS INFORMATION. 3. Install the door finisher with a new switch finisher listed in PARTS INFORMATION. \- Refer to the ESM, section INT\-Interior, for installation procedure. See this bulletin for further detail.
- [PC255](/bulletins/10192273.md), 2021-05-10, Service bulletin: STRUCTURE; EQUIPMENT. Nissan is conducting a Dealer Service Action to inspect for water leaks at the rear liftgate glass on certain specific 2014 Nissan Rogue vehicles currently in dealer inventory.

JSON: [/v1/bulletins/10192617](/v1/bulletins/10192617)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%20NTB15070&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F10192617&vehicle=Service%20bulletin%20NTB15070)