# Service bulletin PC249

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 10192250
- Published by NHTSA: 2021\-05\-10
- Manufacturer's number: PC249
- Manufacturer's date: 2013\-10\-11
- NHTSA component: STRUCTURE

## NHTSA's summary

Nissan is conducting a dealer inventory inspection to inspect the floor support welds on specific MY14 Altima vehicles.

## The document

- [NHTSA's copy of the document (PDF)](https://static.nhtsa.gov/odi/tsbs/2013/MC-10192250-0001.pdf)
- [If that address does not open, try this one](https://static.nhtsa.gov/odi/tsbs/2013/MC-10192250-9999.pdf)

The document is the manufacturer's. This site does not hold it.

## Components

Body and frame

## Vehicles listed

- 2014 NISSAN ALTIMA

## Recalls for the same vehicles and component

- [2020242](/recalls/tc/2020242.md), 2020-05-29: Structure
- [2015083](/recalls/tc/2015083.md), 2015-02-25: Structure

## Other bulletins for the same vehicles and component

- [NTB09\-131C](/bulletins/11031705.md), 2026-04-29, Service bulletin: STRUCTURE:BODY. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS \(Federal Motor Vehicle Safety Standards\) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” \(metal plate or vinyl label\) is attached to the instrument panel or body on the driver side at the base of the windshield \(see Figure 1\). · The “Certification Label” \(vinyl adhesive label\) is located on the lower area of the driver side B\-Pillar \(see Figure 1\).
- [NTB09\-131C](/bulletins/11031704.md), 2026-04-29, Service bulletin: STRUCTURE:BODY. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS \(Federal Motor Vehicle Safety Standards\) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” \(metal plate or vinyl label\) is attached to the instrument panel or body on the driver side at the base of the windshield \(see Figure 1\). · The “Certification Label” \(vinyl adhesive label\) is located on the lower area of the driver side B\-Pillar \(see Figure 1\).
- [NTB13\-028H](/bulletins/10232658.md), 2023-03-07, Service bulletin: VISIBILITY; STRUCTURE. REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- [NTB09\-081J](/bulletins/10232656.md), 2023-03-07, Service bulletin: VISIBILITY; STRUCTURE. WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- [NTB13109A](/bulletins/10192491.md), 2021-05-10, Service bulletin: STRUCTURE. SERVICE INFORMATION If one or both Intelligent Keys cannot be located prior to customer delivery of an Applied Vehicle, refer to the applicable section of this bulletin for Intelligent Key registration instructions. \- One \(1\) Intelligent Key Is Lost \-\-\-\-\- Page 2 \- Two \(2\) Intelligent Keys Are Lost \-\-\-\-\- Page 3 See this bulletin for further detail.
- [NTB14060A](/bulletins/10192471.md), 2021-05-10, Service bulletin: STRUCTURE; ENGINE. SERVICE INFORMATION A two\-piece design front engine mount is currently being used for the applied vehicles listed. A single thunk noise may be heard on the first acceleration of the day from this type of mount and is considered normal operation. The mount has also been designed with built in free\-play that is normal. Under normal driving conditions: \* A "thunk" noise may be heard on the first acceleration of the day. And \* Does not occur again, or at any other time. DO NOT REPLACE THE MOUNT: \* If it has free play or a "single event" thunk sound on the first acceleration of the day. This is considered a normal characteristic of this type of engine mount. \* If a shift shock condition is present when shifting from park into gear or between any combination of gears. This condition is due to transmissions line pressures and not movement of the mount. NOTE: Refer to the Electronic Service Manual section TM \- Transaxle \& Transmission for further diagnostic information on shift shock. See this bulletin for further details.
- [NTB14016A](/bulletins/10192436.md), 2021-05-10, Service bulletin: EQUIPMENT; VISIBILITY:SUN/MOON ROOF ASSEMBLY; STRUCTURE. IF YOU CONFIRM A squeaking/ticking noise is coming from the Headliner between the Moonroof and B\-pillar area shown in Figure A. \* Can occur on rough roads or during conditions that cause body flex such as when entering or exiting a sloped driveway. ACTION Remove Moonroof brackets and apply UHMW tape, from Squeak and Rattle kit J\-50397 \(part \# J\-50397\-15\), to the bracket. Please see this bulletin for further details.
- [NTB13041A](/bulletins/10192370.md), 2021-05-10, Service bulletin: STRUCTURE:BODY:HOOD; EQUIPMENT. SERVICE INFORMATION \- The Applied Vehicles are equipped with a hood ledge finisher on the passenger \(RH\) side only. \- Do not submit a claim for a "missing" hood ledge finisher on driver's \(LH\) side. See this bulletin for further detail.
- [PC256](/bulletins/10192288.md), 2021-05-10, Service bulletin: EQUIPMENT; STRUCTURE. Nissan is conducting a dealer inventory inspection to inspect the floor support welds on certain specific MY14 Altima and Maxima vehicles.
- [NTB13103](/bulletins/10192272.md), 2021-05-10, Service bulletin: STRUCTURE. IF YOU CONFIRM: Contact marks on the painted surface of the body are visible anywhere along the forward edges of either rear combination lamp. ACTION: 1. Using standard auto body repair practices, perform a Refinish Half\-Block Repair to the area\(s\) affected by the rear combination lamp\(s\). 2. Apply a piece of protective urethane tape \(see PARTS INFORMATION\) on both sides of the vehicle where shown in the SERVICE PROCEDURE of this bulletin. See this bulletin for further detail.

JSON: [/v1/bulletins/10192250](/v1/bulletins/10192250)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%20PC249&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F10192250&vehicle=Service%20bulletin%20PC249)