WenmarOpen by Wenmar Pro

Service bulletin 25-001-13

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10189383
Published by NHTSA2021-03-29
Manufacturer's number25-001-13
Manufacturer's date2013-01-25
NHTSA componentBACK OVER PREVENTION

NHTSA's summary

MIL Illumination Due to P2000, P2A00 and/or P2A01 This bulletin involves verifying all service bulletins related to high sooting issues have been properly addressed, inspecting both Oxygen (O2) sensors and either cleaning the sensors or replacing sensors, and installing an O2 Sensor Shield on the exhaust pipe in the area of the FRONT O2 sensor. Customer may experience MIL illumination. Further investigation by the technician may find one or more of the following DTC(s) present: ? P2000 - NOX Absorber Efficiency Below Threshold - Bank 1. ? P2A00 - O2 Sensor 1/1 Circuit Performance. ? P2A01 - O2 Sensor 1/2 Circuit Performance.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Driver assistance, Backup camera

Trouble codes named

P2000, P2A00, P2A01

Vehicles listed
DODGE RAM 25002010 (the catalog's model; the bulletin names a series or trim of it)
DODGE RAM 35002010 (the catalog's model; the bulletin names a series or trim of it)
RAM 25002009
RAM 35002007 to 2009

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
S21230000112022-09-26. Service bulletin. Rattle Tapping Fluttering Noise From A Pillar Or Dash Driving At Highway Speeds
25-004-152022-08-08. Service bulletin. On Board Diagnosis (OBD) Monitor Readiness
25-004-122022-07-25. Service bulletin. Malfunction Indicator Lamp Illumination Due To Oxygen Sensor This bulletin involves replacement of the Oxygen Sensor Connectors for any Oxygen Sensor related DTC. Do NOT replace any parts prior to performing this bulletin and the Verifications test below. If the vehicle has any of the following DTC?s for O2 Sensors, Stored, Pending or Active, perform the Repair Procedure. ? P013A O2 Sensor 1/2 Slow Response - Rich To Lean (Soot related code, see note) ? P013B O2 Sensor 1/2 Slow Response - Lean To Rich (Soot related code, see note) ? P014C O2 Sensor 1/1 Slow Response - Rich To Lean (Soot related code, see note) ? P014D O2 Sensor 1/1 Slow Response - Lean To Rich (Soot related code, see note) ? P0030 O2 Sensor 1/1 Heater Circuit ? P0031 O2 Sensor 1/1 Heater Circuit Low ? P0032 O2 Sensor 1/1 Heater Circuit High ? P0036 O2 Sensor 1/2 Heater Circuit Malfunction ? P0037 O2 Sensor Heater Circuit Low 1/2 ? P0038 O2 Sensor Heater Circuit High 1/2 ? P0053 O2 Sensor Heater 1/1 Resistance ? P0054 O2 Sensor Heater 1/2 Resistance ? P064D Internal Control Module 02 Sensors Processor Performance - Bank 1 ? P0131 1/1 02 Sensor Shorted To Ground ? P0132 1/1 02 Sensor Shorted To Voltage ? P0135 O2 Sensor 1/1 Heater Performance ? P0137 1/2 02 Sensor Shorted To Ground ? P0138 1/2 02 Sensor Shorted To Voltage ? P0141 O2 Sensor 1/2 Heater Performance ? P113C O2 Sensor Power Supply Circuit Performance ? P2195 O2 Sensor 1/1 Out Of Range High ? P2196 O2 Sensor 1/1 Out Of Range Low ? P22AB O2 Sensor Positive Current Control Circuit/Open - Bank 1 Sensor 2 ? P22AE O2 Sensor Reference Voltage Circuit/Open - Bank 1 Sensor 2 ? P22B2 O2 Sensor Negative Current Control Circuit/Open - Bank 1 ? P22B5 O2 Sensor 1/2 Pump Cell Current Trim Circuit Open ? P2237 O2 Sensor 1/1 Pump Cell Current Circuit Low ? P2243 O2 Sensor 1/1 Reference Voltage Circuit Open ? P2251 O2 Sensor 1/1 Negative Current Control Circuit/Open ? P2270 O2 Sensor 1/2 Out Of R
25-004-152022-07-25. Service bulletin. On Board Diagnosis (OBD) Monitor Readiness
18-005-132021-03-29. Service bulletin. Flash: Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM) with new software.Trucks exhibiting any DTC related to Oxygen Sensor, Oxygen Sensor Module or communication to the Oxygen Sensor Module also require that Service Bulletin?s 25-004-12 (or later bulletin) must be performed (if not previously performed). Pick up trucks equipped with a 6.7L Cummins diesel have a number of software improvements/enhancements available. This SB will include improved robustness for DTC's: P2000 - NOX ABSORBER EFFICIENCY BELOW THRESHOLD P1451 - DIESEL PARTICULATE FILTER SYSTEM PERFORMANCE P0101 - MASS AIR FLOW SENSOR "A" CIRCUIT PERFORMANCE P046C - EGR POSITION SENSOR PERFORMANCE P049D - EGR CONTROL POSITION EXCEEDED LEARNING LIMIT P051B - CRANKCASE PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE P2002 - DIESEL PARTICULATE FILTER EFFICIENCY BELOW THRESHOLD P2262 - TURBOCHARGER BOOST PRESSURE NOT DETECTED - MECHANICAL P2609 - INTAKE AIR HEATER SYSTEM PERFORMANCE P245B - EGR COOLER BYPASS STATUS LINE INTERMITTENTVehicles flashed to address the above codes should be driven and repair validated. If code(s) return, follow diagnostic procedures available in DealerCONNECT/TechCONNECT.Improvements other than DTC robustness or enhancements: O2 Sensor cleaning cycle Correct Charge Air Cooler (CAC) out voltage reading in WiTech Improve idle shutdown messages Add ability to read Exhaust Manifold Presure (EMP) sensor value in WiTech Display correct Exhaust Gas Recirculation (EGR) position in WiTech Make Grid Heater off time selectable in WiTec Display correct alternator voltage in WiTech Turn Low Voltage Idle Up Off MIL on with no DTC Ability to read EGR valve gap on wiTECH Erroneous, brief brake lamp flash at key onSecure Bootloader softwareIf the Engine Control Module (ECM) does not have a calibration installed, or has an unapproved calibration installed then the ECM will
25-002-142018-06-11. Service bulletin. Malfunction Indicator Lamp Illumination Due To Oxygen Sensor This bulletin involves the installation of an Oxygen (O2) Sensor Overlay Harness for any Oxygen Sensor related DTC(s). The Overlay Harness will consist of twelve 18 AWG wires (six from each Oxygen Sensor) that run to a new Oxygen Sensor Module connector. Four wires will be removed from the original vehicle O2 Module connector and installed in the new overlay harness O2 Module connector.Do NOT replace any parts prior to performing this bulletin and the Verifications test below. If the vehicle has any of the following DTC?s for O2 Sensors, Stored, Pending or Active, perform the Repair Procedure. P013A O2 Sensor 1/2 Slow Response - Rich To Lean (Soot related code, see note). P013B O2 Sensor 1/2 Slow Response - Lean To Rich (Soot related code, see note). P014C O2 Sensor 1/1 Slow Response - Rich To Lean (Soot related code, see note)P014D O2 Sensor 1/1 Slow Response - Lean To Rich (Soot related code, see note) P0030 O2 Sensor 1/1 Heater Circuit P0031 O2 Sensor 1/1 Heater Circuit Low P0032 O2 Sensor 1/1 Heater Circuit High P0036 O2 Sensor 1/2 Heater Circuit Malfunction P0037 O2 Sensor Heater Circuit Low 1/2 P0038 O2 Sensor Heater Circuit High 1/2 P0053 O2 Sensor Heater 1/1 Resistance P0054 O2 Sensor Heater 1/2 Resistance P064D Internal Control Module 02 Sensors Processor Performance - Bank 1 P0131 1/1 02 Sensor Shorted To Ground P0132 1/1 02 Sensor Shorted To Voltage P0135 O2 Sensor 1/1 Heater Performance P0137 1/2 02 Sensor Shorted To Ground P0138 1/2 02 Sensor Shorted To Voltage P0141 O2 Sensor 1/2 Heater Performance P113C O2 Sensor Power Supply Circuit Performance P2195 O2 Sensor 1/1 Out Of Range High P2196 O2 Sensor 1/1 Out Of Range Low P22AB O2 Sensor Positive Current Control Circuit/Open - Bank 1 Sensor 2 P22AE O2 Sensor Reference Voltage Circuit/Open - Bank 1 Sensor 2 P22B2 O2 Sensor Negative Current Control Circuit/Open - Bank 1 P22B5 O2 Sensor 1/2 Pump Cel
90027352018-06-11. Service bulletin. Part Description: Park View Rear Back-Up Camera Kit Issue Description: The wiring instructions for the Mopar accessory Backup Camera kit has changed on the Ram 2011 and 2012 model years.The L1 Circuit is WT/RD. Please make sure the instruction sheet supplied in the kit has the date of December 01, 2010. If the instruction sheet does not have this date then use TechCONNECT to get the most updated instructions. Go under the Service Info tab and select Mopar Accessories, Audio and Electronics, Instruction Sheet, Backup Camera.