WenmarOpen by Wenmar Pro

Service bulletin TSB 19-2365

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10169811
Published by NHTSA2020-01-07
Manufacturer's numberTSB 19-2365
Manufacturer's date2019-12-06
NHTSA componentENGINE AND ENGINE COOLING

NHTSA's summary

Some 2018-2020 F-150 vehicles equipped with a 5.0L engine may exhibit excessive oil consumption of greater than 1L (1 quart) in 4,800 km (3,000 mi) with no visible oil leaks. This may be due to high intake manifold vacuum during some deceleration fuel shut off (DFSO) events resulting in oil being pulled into the combustion chamber from the crankcase, valve guides, and positive crankcase ventilation (PCV). To correct the condition, follow the Service Procedure steps to reprogram the powertrain control module (PCM), install a new engine oil level indicator and change the engine oil and oil filter. The revised PCM calibration reduces engine vacuum during some DFSO events.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Engine

Vehicles listed
FORD F-1502018, 2019, 2020

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
19V2780002019-04-08. ENGINE; EQUIPMENT:ELECTRICAL
18V8940002018-12-18. ENGINE
20175152017-10-24. Engine
17V6720002017-10-23. ENGINE

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SSM 552282026-10-12. Service bulletin. Some 2020-2026 Aviator/Explorer/F-150/Bronco/Ranger vehicles equipped with a 2.7L or 3.0L (non-diesel) engine may need the front engine cover removed and reinstalled for various reasons. The Workshop Manual (WSM), Section 303-01 Engine > Removal and Installation > Engine Front Cover service procedure has been updated to include a new essential special service tool (ESST) guide pin alignment tool (303-1790) that is used to align the engine front cover to the engine block, preventing the O-ring seal on the engine oil galley feed tube from getting damaged during installation.
SSM 542622025-10-07. Service bulletin. Some 2019-2020 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost, 2020 Aviator vehicles equipped with a 3.0L EcoBoost or 3.0L plug-in hybrid electric vehicle (PHEV) engine, 2020 Explorer vehicles equipped with a 3.0L EcoBoost, and 2020 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine. This noise may occur on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to an internal component of the variable cam timing (VCT) unit. If diagnostics lead to the VCTs as the source of the noise, refer to the 2024 F-150 Workshop Manual (WSM), Section 303-00 > Diagnosis and Testing > Engine > Pinpoint Test F. Pinpoint test F has been updated to include additional steps along with a video on how to identify the single affected VCT unit that requires replacement.
SSM 537642025-05-21. Service bulletin. Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
SSM 527722024-08-16. Service bulletin. Some 2020-2024 F-150, 2021-2024 Bronco, and 2024 Ranger vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a stuck internal component of the variable cam timing (VCT) unit.
TSB 24-21152024-05-04. Service bulletin. This article supersedes TSB 22-2260 to update the vehicle applications. Some 2018-2020 F-150 vehicles equipped with a 2.7L EcoBoost may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0420 and/or P0430 stored in the powertrain control module (PCM). This may be due to calibration and controls sensitivity.
SSM 524472024-05-03. Service bulletin. Some 2020-2024 F-150 and 2021-2024 Bronco vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a stuck internal component of the variable cam timing (VCT) unit. To correct the condition, replace all 4 of the VCT units following Workshop Manual (WSM), Section 303-01. For claiming, use causal part 6C525 and applicable labor operations in Section 6 of the Service Labor Time Standards (SLTS) Manual. If labor times are not available, claim M-time.
SSM 523352024-03-20. Service bulletin. For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 523342024-03-20. Service bulletin. Some 2011-2024 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a tick tap and/or typewriter ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150°F (65°C) or higher and engine speed is at idle up to approximately 1700 RPM. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise tick rate can be faster or slower and is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted. This information along with an example audio clip has been added to the WSM Section 303-00 Engine System General Information > Diagnosis and Testing > Engine > PPT F > Step F2.
TSB 23-21432023-05-31. Service bulletin. Some 2017-2020 F-150 and 2018-2020 Expedition/Navigator vehicles built on or before 30-Nov-2019 and equipped with a 3.5L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. Some vehicles may also exhibit an intermittent condition with no auto restart during auto-start-stop operation with or without diagnostic trouble code (DTC) P164C present in the powertrain control module (PCM). This may be due to a worn variable camshaft timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
SSM 516652023-05-29. Service bulletin. Some 2021-2023 Ford and Lincoln vehicles equipped with a 2.7L or 3.0L engine may exhibit an upper engine thump/knock noise coming from the left cylinder head. This condition is most noticeable at idle and may lessen at higher engine speed or while driving. This condition does not affect vehicle durability and will not get worse over time. Use a stethoscope or chassis ears and listen just behind the left cylinder head intake VCT solenoid on the cam cover to determine if the thump/knock noise is coming from the cylinder head/camshaft. The left cylinder head and the camshaft roller followers are available as service parts.