Service bulletin 9004116
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10166548 |
| Published by NHTSA | 2019-10-28 |
| Manufacturer's number | 9004116 |
| Manufacturer's date | 2019-08-28 |
| NHTSA component | SEATS |
NHTSA's summary
HANDLE AND CABLE, Seat Release If you have a 2 door JL with EZ entry handle that is loose or appears broken follow the procedure below. Mounting bracket has grease present which may have damaged plastic part. Please call Adam Rose (586) 804-4315) for cleaning procedure prior to replacing any parts. If no response in 15 minutes, proceed with repair after thoroughly cleaning grease off metal mounting bracket as follows. Clean metal mounting bracket with brake cleaner sprayed onto shop rag, rub on mounting surface until grease is removed. Do not spray brake cleaner directly onto seat. Replacement plastic part may fail in same way if grease is not removed.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Seats
| JEEP GLADIATOR | 2020 |
|---|---|
| JEEP WRANGLER | 2018, 2019 |
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 2020456 | 2020-09-25. Seats And Restraints |
|---|---|
| 18V231000 | 2018-04-12. SEATS:MID/REAR ASSEMBLY; STRUCTURE:FRAME AND MEMBERS |
A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.
| S2323000081 | 2024-01-16. Service bulletin. Buzz Squeak Rattle (BSR) From Rear Seat Area. |
|---|---|
| 85230 | 2023-01-09. Service bulletin. CABLE - FRONT SEAT |
| S2023000036 | 2023-01-09. Service bulletin. Front Seat Lift Handle Binding |
| 1804822 | 2023-01-09. Service bulletin. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs: P0300 - Multiple Cylinder Misfire.If DTC P0300 is present either alone or along with other DTCs listed within thisbulletin the right intake camshaft MUST be replaced along with this software update (only if DTC P0300 is present). Refer to the detailedservice procedures available in DealerConnect>Service Library under: Service Info>09 - Engine, 3.6L / Cylinder Head / Camshaft, Engine / Removal and Installation>Right. If just the software flash was done without the right intake camshaft being replacedthe DTC P0300 may reoccur.If DTC P0300 is not present but other DTCs on this list below are present, performjust the software update. P0441 - EVAP Purge System Performance. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will nowbe P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the following: The Anti-Lock Brake System (ABS) light illuminates. The customer may notice an ability to shift into 1st gear at an unsafespeed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active. |
| 1804822 | 2022-10-17. Service bulletin. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs: P0300 - Multiple Cylinder Misfire.If DTC P0300 is present either alone or along with other DTCs listed within thisbulletin the right intake camshaft MUST be replaced along with this software update (only if DTC P0300 is present). Refer to the detailedservice procedures available in DealerConnect>Service Library under: Service Info>09 - Engine, 3.6L / Cylinder Head / Camshaft, Engine / Removal and Installation>Right. If just the software flash was done without the right intake camshaft being replacedthe DTC P0300 may reoccur.If DTC P0300 is not present but other DTCs on this list below are present, performjust the software update. P0441 - EVAP Purge System Performance. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will nowbe P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the following: The Anti-Lock Brake System (ABS) light illuminates. The customer may notice an ability to shift into 1st gear at an unsafespeed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active. |
| S2023000036 | 2022-09-26. Service bulletin. Front Seat Lift Handle Binding |
| 9003704 | 2022-09-26. Service bulletin. Transmission Oil Pan, Heater (TMU), Tube or O-ring Applies to vehicles equipped with 8 speed transmissions only; if you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair. |
| 2302122 | 2022-09-26. Service bulletin. Front Seat Will Not Unfold and Lock Into Position This bulletin involves replacing the Easy Entry release cable and both front seattrack seat position returns. Customers may experience one or both of the following: This may be an intermittent condition the customer experiences.One or both of the front seats will not unlock from the Easy Entry position. One or both of the front seats will not unfold and lock back into the upright position. The vehicle cannot be driven due to this condition. |
| 2302021 | 2022-09-26. Service bulletin. Front Passenger Outer Seat Bolster Foam is Collapsed This bulletin includes repositioning the passenger outer seat bolster and installing a strap and push pin to help prevent this concern from happening again. Customers may comment on the following: The front passenger outer seat bolster cushion is missing |
| 9004175 | 2022-09-15. Service bulletin. LATCH, Folding Top For a concern of a loose latch in the closed position, it is not necessary to replace the latch unless broken. Refer to instructions in service library. The position of the receiver attached to the vehicle header can be adjusted to change the ammount of force required to latch. |