# Service bulletin SSM 47526

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 10149763
- Published by NHTSA: 2018\-12\-03
- Manufacturer's number: SSM 47526
- Manufacturer's date: 2018\-09\-19
- NHTSA component: STEERING

## NHTSA's summary

Some 2018 EcoSport vehicles equipped with a rear parking aid camera may intermittently exhibit the active reverse guideline overlays not present on the front display interface module \(FDIM\) when reverse gear is selected. This may be due to the steering straight ahead position not stored into the power steering control module \(PSCM\). Reprogram the PSCM to GN15\-14C217\-AE or later using the latest version of the appropriate Ford scan tool. Operation of the active reverse guidelines would be restored after the vehicle is driven in a straight ahead direction with minimal steering input/effort at a speed of over 40 mph \(64 km/h\). For claiming, use causal part 3C529 and applicable labor operations in Section 03 of the Service Labor Time Standards \(SLTS\) Manual.

## The document

- [NHTSA's copy of the document (PDF)](https://static.nhtsa.gov/odi/tsbs/2018/MC-10149763-9999.pdf)
- [If that address does not open, try this one](https://static.nhtsa.gov/odi/tsbs/2018/MC-10149763-0001.pdf)

The document is the manufacturer's. This site does not hold it.

## Components

Steering

## Vehicles listed

- 2018 FORD ECOSPORT

## Other bulletins for the same vehicles and component

- [SSM 47489](/bulletins/10144947.md), 2018-09-24, Service bulletin: STEERING. When connecting the Vehicle Communication Module \(VCM\) and Integrated Diagnostic System \(IDS\) or Ford Diagnosis and Repair System \(FDRS\) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes \(DTCs\), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
- [SSM 47268](/bulletins/10137148.md), 2018-05-21, Service bulletin: STEERING:ELECTRIC POWER ASSIST SYSTEM; BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. Some 2018 EcoSport vehicles equipped with rear parking aid camera may intermittently exhibit the active reverse guideline overlays not present on the front display interface module \(FDIM\) when reverse gear is selected. This may be due to the steering straight ahead position not stored into the power steering control module \(PSCM\). Operation of the active reverse guidelines are restored after the vehicle is driven in a forward direction and reverse gear is selected during the drive cycle. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.

JSON: [/v1/bulletins/10149763](/v1/bulletins/10149763)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%20SSM%2047526&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F10149763&vehicle=Service%20bulletin%20SSM%2047526)