Service bulletin 21-047-15

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10149686
Published by NHTSA	2018-12-03
Manufacturer's number	21-047-15
Manufacturer's date	2015-07-18
NHTSA component	POWER TRAIN

NHTSA's summary

Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. The customer may describe one or more of the following: ? Harsh 1-2 Upshift. ? Harsh Garage Shifts (Park to Reverse or Drive).

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Transmission and driveline

Vehicles listed
FIAT 500	2016

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
16V302000	2016-05-16. POWER TRAIN:MANUAL TRANSMISSION
2016217	2016-05-12. Powertrain

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
9003791	2022-10-31. Service bulletin. 1.4L FIRE Service Engine (Normally Aspirated) This engine in this kit will contain one of 8 different production full dress engines, but labeled as component engine 68275870AA or 71AA. The received engine will be configured for use with an automatic transmission, (includes auto transmission adapter plate / flexplate) or manual transmission. (includes flywheel / clutch asm) The received engine will be configured with or without a block heater. If required, dealer to purchase/install the block heater. The included instruction sheet K6855863AB in engine kit 68275870AA is to be followed for all applications that it applies. Please see the sheet for details. In addition to the items detailed in instruction sheet K6855863AB, please read the following below to determine the rework required to install this engine into a 2012- 2018 Fiat 500 (FF) with 1.4L EAB normally aspirated engine: 1) determine which condition exists for the received service engine a) vehicle has a manual transmission, received manual transmission engine. b) vehicle has a manual transmission, received automatic transmission engine. c) vehicle has an automatic transmission, received automatic transmission engine. d) vehicle has an automatic transmission, received manual transmission engine. 2) follow below steps based on condition (a) through (d) above. Condition a) No further rework required, other than ordering/installing a block heater if required. Condition b) Remove flexplate / auto trans adapter plate / auto trans engine mounting bracket / auto trans engine oil dipstick from new service engine. Transfer flywheel / clutch / manual trans engine mounting bracket / manual trans engine oil dipstick from old engine. Order/install block heater if required. Condition c) Identify the automatic transmission adapter plate on the original engine. Looking at the rear of the vehicle engine with adapter plate mounted:
S1821000001	2022-09-26. Service bulletin. Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009	2022-09-26. Service bulletin. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
RL305553A	2022-09-15. Service bulletin. 9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
RL305553A	2022-08-22. Service bulletin. 9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
21-053-15	2022-08-08. Service bulletin. 948TE 9 Speed Transmission Quick Learn Procedure This bulletin provides information on how to perform the new scan tool based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality may be erratic.
21-055-15	2022-07-25. Service bulletin. Flash: Vehicle Will Not Shift Out Of Park This bulletin involves reprogramming the Electronic Shift Module (ESM) with the latest available software. Some Customers may experience a condition where the vehicle will not shift out of park while the engine running at idle and brake pedal applied. Cycling the ignition key off and restarting the engine will allow shift. Technicians may find DTC P0606-00 Control Module Processor. Flashing the ESM with the latest software will correct this concern.
21-053-15	2022-07-25. Service bulletin. 948TE 9 Speed Transmission Quick Learn Procedure This bulletin provides information on how to perform the new scan tool based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality may be erratic.
21-038-15 REV-B	2018-12-17. Service bulletin. Flash: Drivetrain Control Module (DTCM) C2020-01 ECU Internal Fault setting in the DTCM This bulletin involves reprogramming the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience the All Wheel Drive Light (AWD) illuminating due to DTC C2020-01 ECU Internal Fault setting erroneously in the DTCM.
21-055-15	2018-12-17. Service bulletin. Flash: Vehicle Will Not Shift Out Of Park This bulletin involves reprogramming the Electronic Shift Module (ESM) with the latest available software. Some Customers may experience a condition where the vehicle will not shift out of park while the engine running at idle and brake pedal applied. Cycling the ignition key off and restarting the engine will allow shift. Technicians may find DTC P0606-00 Control Module Processor. Flashing the ESM with the latest software will correct this concern.