WenmarOpen by Wenmar Pro

Service bulletin B513716

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10146834
Published by NHTSA2018-11-05
Manufacturer's numberB513716
Manufacturer's date2016-09-01
NHTSA componentWHEELS

NHTSA's summary

REWORKING THE PVC SEAM SEAL ON THE RIGHT REAR WHEEL ARCH. PVC Seam Sealer on the right rear inner wheel arch may not have been properly applied. Ineffective manufacturing procedure.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Wheels

Vehicles listed
BMW 328D2016, 2017
BMW 328I2016
BMW 330I2017
BMW R 1200 GS ADVENTURE2017 (the catalog's model; the bulletin names a series or trim of it)

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
B3405152020-12-21. Service bulletin. TICKING NOISE FROM THE FRONT AXLE WHEN CORNERING: The customer may complain of a metallic ticking noise from the front axle, when cornering, maneuvering, parking or pulling away from a parking space.
B3405172020-08-31. Service bulletin. TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: Ticking noise coming from front wheel while cornering without brakes applied, noticeable at low speeds. The vehicle must be moving.
B0126182020-06-15. Service bulletin. EPS STEERING ELECTRIC MOTOR MOUNTING BOLTS - LTD WTY EXT TO 10 YRS/120000 MILES: There are front end noises when turning the steering wheel and/or there is limited power steering assist when maneuvering or parking the vehicle. For the basic steering gears one possible cause is that the mounting bolts for the electric motor may become loose missing and/or broken due to corrosion.
B3405172020-04-20. Service bulletin. TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.
MC36001182019-05-20. Service bulletin. During the course of quality analysis, it was determined by BMW Motorrad that in the production period from February 2018 to end of June 2018, cross-spoked wheels with reduced spoke tension have been produced.
B6103152018-12-10. Service bulletin. Various Check Control Messages Caused by Shorted K-CAN This Service Information bulletin supersedes SI B61 03 15 dated April 2016. The customer states that one or more of the following CC messages are displayed: 627 - Steering behavior:Drive moderately 070 - Steering: Drive moderately 765 - Rear-end collision restricted 850 - Pedestrian warning restricted 236 - Driving stabilization: Drive moderately 299 - SOS call system failure 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter FEM - D91DE0 No message, receiver FEM, transmitter TMSL FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ACSM - C9540C Message missing, receiver ACSM, transmitter FEM TMSL - D95402 Message missing, receiver TMSL, transmitter FEM KOMBI - E11454 No message, receiver KOMBI, transmitter REM FEM - D91DE6 No message, receiver FEM, transmitter TMSL TMSR - D99401 Message missing, receiver TMSR, transmitter FEM TMSR - D99402 Message missing, receiver TMSR, transmitter FEM FEM - 8041BA AHL system faulty FEM - D916C3 No message, receiver FEM, transmitter TCB ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM TMSL- D95401 Message missing, receiver TMSR, transmitter FEM HU-H - S0397 MOST configuration was not stored TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault FEM - 8041B6 LWR faulty REM - E58468 Body CAN2; communication fault TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted K-CAN wiring under driver or passenger seat Shorted K-CAN2 wires were shorted between the left side trunk trim panel and the body of the vehicle Shorted K-CAN in left rear wheel well area Shorted K-CAN under center console trim Shorted K-CAN under A-Pill
B3601152018-11-13. Service bulletin. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
3408142018-11-13. Service bulletin. "SUBJECT Ticking Noise from Front Axle When Cornering. Covered under the terms of the BMW New Vehicle/SAV Limited Warranty. Defect Code:34 11 00 57 00Labor Operation:Labor Allowance:Description:34 11 220Refer to KSDRemoving and installing both front brake discsAnd:34 99 0002 FRUWork time for sanding hub surface of brake discs and cleaning wheel hub surfacesLabor operation code 34 11 220 is a Main labor operation. If you are using a Main labor code for another repair, use the Plus code labor operation 34 11 609 instead. With the front brake calipers removed, use 34 11 612, or with the front brake pads removed, use 34 11 613. Refer to KSD2 for the corresponding flat rate unit (FRU) allowance. Enter the Chassis Number, which consists of the last 7 digits of the Vehicle Identification Number (VIN). Click on the ""Search"" button, and then enter the applicable flat rate labor operation in the FR code field. Even though work time labor operation code 34 99 000 ends in ""000"", it is not considered a Main labor operation. Also, since the ""work time"" FRU allowance to be claimed is specified, a separate punch time is not required."
B2704152018-11-05. Service bulletin. Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
B3408142018-11-05. Service bulletin. Ticking Noise from Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a light metallic ticking from the front outer cornering wheel. Movement between the brake disc and wheel bearing hub.