# Service bulletin 03\-001\-17

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 10140024
- Published by NHTSA: 2018\-06\-11
- Manufacturer's number: 03\-001\-17
- Manufacturer's date: 2017\-03\-10
- NHTSA component: VEHICLE SPEED CONTROL

## NHTSA's summary

Noise In Front Of Vehicle When Accelerating Or Decelerating This bulletin involves replacing both front half shafts. The customer may describe a clunk type noise in front of the vehicle while accelerating or decelerating.

## The document

- [NHTSA's copy of the document (PDF)](https://static.nhtsa.gov/odi/tsbs/2017/MC-10140024-9999.pdf)
- [If that address does not open, try this one](https://static.nhtsa.gov/odi/tsbs/2017/MC-10140024-0001.pdf)

The document is the manufacturer's. This site does not hold it.

## Components

Throttle and cruise control

## Vehicles listed

- 2015 to 2017 JEEP RENEGADE

## Other bulletins for the same vehicles and component

- [2310423](/bulletins/10247471.md), 2023-12-18, Service bulletin: VEHICLE SPEED CONTROL. Front Side Window Contour Seal Deformation One or both front door side window seals are deformed Fig. 1. This bulletin involves replacing the window seal and glass.
- [2303514](/bulletins/10232026.md), 2023-02-21, Service bulletin: LATCHES/LOCKS/LINKAGES:DOORS:LATCH; SEAT BELTS; VEHICLE SPEED CONTROL. Driver Door Lock Cylinder
- [2302015](/bulletins/10229243.md), 2023-01-09, Service bulletin: VEHICLE SPEED CONTROL; PARKING BRAKE; EQUIPMENT. Replace Missing Manual Release Cover For The Electric Fuel Door This bulletin involves installing a cover for the fuel door manual release cable. The customer may describe a loose cable hanging in the right rear of the cargo compartment area.
- [0802116](/bulletins/10224863.md), 2022-10-31, Service bulletin: ELECTRICAL SYSTEM; VEHICLE SPEED CONTROL; STRUCTURE; AIR BAGS; SEAT BELTS. Flash: BCM Diagnostic And System Improvements This bulletin involves reprogramming the Body Control Module \(BCM\) with the latest available software. The customer may describe one or more of the following: · \*\*Rear interior overhead lamps remain illuminated after exiting vehicle and locking from the driver's or passenger's door lock buttons. This is causing the vehicle battery to go dead.\*\* · The door locks are inoperative when locking/unlocking remotely. · False activation of the vehicle security alarm. · False exterior light failure messages being displayed in the instrument cluster.
- [06106092A](/bulletins/10221557.md), 2022-09-26, Service bulletin: VEHICLE SPEED CONTROL; ELECTRICAL SYSTEM; POWER TRAIN; STRUCTURE. Seat Relay For a Jeep Renegade or Fiat 500X ONLY, if the driver's power seat will not move in any axis and the key is in the on position with the door open: 1. Please take a Vehicle Scan Report, taking note of any active or stored DTC's, especially in the Body Control Module \(BCM\). 2. Before replacing the relay, call Rick Gordon at cell \(248\) 630\-6281. If no answer leave a message and if after 15 minutes, there is no return call, proceed with the repair. 3. In the event there is no call\-back, please email the Vehicle Scan Report to rick.gordon@fcagroup.com
- [9003413](/bulletins/10219831.md), 2022-09-15, Service bulletin: VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
- [23\-035\-14](/bulletins/10218213.md), 2022-08-22, Service bulletin: AIR BAGS; VEHICLE SPEED CONTROL; PARKING BRAKE; SEAT BELTS. Driver Door Lock Cylinder This bulletin involves replacing the driver door lock cylinder housing. The plastic cover of the driver door lock cylinder may be loose or fall off.
- [23\-042\-15](/bulletins/10209586.md), 2022-04-04, Service bulletin: VEHICLE SPEED CONTROL. The outside door handle cable grommet does not seal effectively for water
- [53034160A](/bulletins/10159998.md), 2019-05-20, Service bulletin: VEHICLE SPEED CONTROL; VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Part Description: Accelerator Pedal Issue Description: Vehicle has accelerator pedal fault code. Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
- [68277402A](/bulletins/10139956.md), 2018-06-11, Service bulletin: VEHICLE SPEED CONTROL:CRUISE CONTROL. Adaptive Cruise Control Sensor 1\) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.\~ 2\) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced \(TCM, PCM, ESP/ABS, etc\). This fault is not due to the ACC Sensor. No sensor replacement is required.\~ 3\) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage \(if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module\), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. \*\*Hints for running Horizontal Alignment procedure: A\) Verify speed is between 45 and 75 mph, B\) verify the road is relatively straight with signs, poles, guard rails, etc C\) Do not tail a vehicle too closely this inhibits the learning procedure

JSON: [/v1/bulletins/10140024](/v1/bulletins/10140024)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%2003-001-17&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F10140024&vehicle=Service%20bulletin%2003-001-17)