Service bulletin PI0874
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10138563 |
| Published by NHTSA | 2018-05-29 |
| Manufacturer's number | PI0874 |
| Manufacturer's date | 2012-12-06 |
| NHTSA component | FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP |
NHTSA's summary
This preliminary information bulletin provides a procedure on replacement of the fuel tank and fuel pipe vent hose for a concern of the malfunction indicator lamp illuminated and DTC P0454.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Fuel system, Fuel tank
Trouble codes named
P0454
| CADILLAC ATS | 2013 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 18207 02 | 2022-05-31. Service bulletin. Customer Satisfaction. Certain vehicles may have a condition in which the power steering gear motor could separate from the steering gear housing due to corrosion of the attaching bolts. If the motor separates, power steering assist may be reduced or lost, and the driver may experience an unexpected increase in steering effort, especially at low speeds. Replace the bolts that attach the electric power steering motor to the steering gear and add a protective wax coating to each bolt and the seam around the electric power steering motor. If the bolts cannot be removed due to corrosion, the steering gear must be replaced. ** Revised Parts Information ** |
|---|---|
| 18207 | 2022-05-31. Service bulletin. Customer Satisfaction. Certain vehicles may have a condition in which the power steering gear motor could separate from the steering gear housing due to corrosion of the attaching bolts. If the motor separates, power steering assist may be reduced or lost, and the driver may experience an unexpected increase in steering effort, especially at low speeds. Replace the bolts that attach the electric power steering motor to the steering gear and add a protective wax coating to each bolt and the seam around the electric power steering motor. If the bolts cannot be removed due to corrosion, the steering gear must be replaced. |
| PIT4943D | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
| PIC6030 | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that may have check engine light on. Technician may find a Diagnostic Trouble Code P0442. Technician will need to inspect the fuel filler pocket rubber insulator to make sure it is not rolled over the fuel pipe neck. |
| PI-0874 | 2013-02-25. Service bulletin. CADILLAC: DUE TO FUEL BEING TRAPPED, IN FUEL TANK VENT LINE, WHEN REFUELING OR DURING MANEUVERS,THE VAPOR COMMUNICATION IS BLOCKED BETWEEN FUEL TANK AND FUEL TANK VAPOR PRESSURE SENSOR, CAUSING THE MALFUNCTION INDICATOR LAMP TO COME ON. MODEL 2013 ATS. *PE |