WenmarOpen by Wenmar Pro

Service bulletin V501603 2038981

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10121112
Published by NHTSA2017-10-31
Manufacturer's numberV501603 2038981
Manufacturer's date2016-02-08
NHTSA componentWHEELS

NHTSA's summary

Document discusses issues with The wheel liner touches the arch area of the fender and rubs off the paint in the contact area. The corrosion is caused by dirt accumulations and movements of the wheel liner. It discusses how to service the corrosion issue, and how to document it

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Wheels

Vehicles listed
VOLKSWAGEN PASSAT2001, 2002, 2003, 2004, 2005, 2006
VOLKSWAGEN PASSAT2008, 2009, 2010, 2011, 2012
VOLKSWAGEN PASSAT WAGON2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010 (the catalog's model; the bulletin names a series or trim of it)

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
TT5014012023-07-10. Service bulletin. The use of tire dressing gives your tires that shiny finish that completes the image of a clean (new) vehicle. There are many different tire dressing products available. When choosing a product please pay close attention to its contents. Always use a water based product.
TT4513012023-07-10. Service bulletin. After replacing a Bosch 5.7 ABS module, refer to the table below to determine correct module coding value based on vehicle PR codes. Listed login code must be entered under Access/authorization before coding is attempted. After completing coding, G85 steering angle sensor basic settings must be performed before cycling key. To perform G85 basic settings manually in Vehicle self-diagnosis (VAS PC) or Control Module OBD (ODIS), start by entering access/authorization code 40168. After code is accepted, turn steering wheel 1 turn left and back to center, one turn right, and then center steering wheel. Select basic settings and enter group 1. Once display changes to ?Sensor OK? or ?Calibration OK?, basic settings have been completed. Cycle key OFF and then back ON. Clear faults to verify repair.
TT45061222023-07-05. Service bulletin. Use the following procedure to diagnose active wheel speed sensor complaints:
TT4414022023-07-05. Service bulletin. This can be the due to the Encoder Ring being ground down on the wheel bearing hub unit, resulting in a damaged part.
TT4413032023-07-05. Service bulletin. This Tech Tip provides an overview of vehicle four wheel alignment, and important steps that should be followed when performing four wheel alignments.
TB5014022023-06-26. Service bulletin. Front Fender - Corrosion on Wheel Arch
TB5014012023-06-26. Service bulletin. Front Fender - Corrosion on Wheel Arch
TB4413042023-06-26. Service bulletin. Four Wheel Alignment Overview, Steering Wheel off Center, Vehicle Drift/Pull
TB4413032023-06-26. Service bulletin. Four Wheel Alignment Overview, Steering Wheel off Center, Vehicle Drift/Pull
TB4413022023-06-26. Service bulletin. This Technical Bulletin provides an overview for performing vehicle four Wheel Alignment, and information on improving vehicle drift/pull using selective tire placement. The information provided is based on the Hunter alignment equipment, Hunter GSP9700 with StraighTrak (VAS 6230x ) and John Bean RFV2000 with OptiLine (VAS 6311A) diagnostic balancer. The alignment information provided in this bulletin is not limited to the Hunter alignment equipment, and still applies with the use of other Volkswagen approved alignment equipment. The diagnostic procedure for selective tire placement, to improve vehicle drift/pull, will require the use of one of the diagnostic balancers previously mentioned.