# Service bulletin NTB17\-108

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 10118713
- Published by NHTSA: 2017\-10\-12
- Manufacturer's number: NTB17\-108
- Manufacturer's date: 2017\-09\-29
- NHTSA component: EXTERIOR LIGHTING; STRUCTURE:BODY:BUMPERS

## NHTSA's summary

2008\-2013 ROGUE AND 2014\-2015 ROGUE SELECT; RUST AROUND REAR LICENSE LAMP FINISHER IF YOU CONFIRM Rust is found on the rear deck lid surface in the area surrounding the license lamp finisher \(Figure 1\) or when replacing the license lamp finisher for any reason. ACTION \- Replace the license lamp finisher with the new replacement part listed the Parts Information. \> Refer to the Electronic Service Manual \(ESM\), section EXT ? Exterior for removal and installation information. \- Repair any damaged surfaces that were in direct contact with the license lamp finisher.

## The document

- [NHTSA's copy of the document (PDF)](https://static.nhtsa.gov/odi/tsbs/2017/MC-10118713-9999.pdf)
- [If that address does not open, try this one](https://static.nhtsa.gov/odi/tsbs/2017/MC-10118713-0001.pdf)

The document is the manufacturer's. This site does not hold it.

## Components

Body and frame, Lighting

## Vehicles listed

- 2008 to 2015 NISSAN ROGUE

## Recalls for the same vehicles and component

- [2016165](/recalls/tc/2016165.md), 2016-04-15: Structure
- [16V219000](/recalls/nhtsa/16V219000.md), 2016-04-15: STRUCTURE:BODY:HATCHBACK/LIFTGATE:SUPPORT DEVICE/STRUT
- [2015334](/recalls/tc/2015334.md), 2015-07-23: Structure

## Other bulletins for the same vehicles and component

- [NTB09\-131C](/bulletins/11031705.md), 2026-04-29, Service bulletin: STRUCTURE:BODY. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS \(Federal Motor Vehicle Safety Standards\) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” \(metal plate or vinyl label\) is attached to the instrument panel or body on the driver side at the base of the windshield \(see Figure 1\). · The “Certification Label” \(vinyl adhesive label\) is located on the lower area of the driver side B\-Pillar \(see Figure 1\).
- [NTB09\-131C](/bulletins/11031704.md), 2026-04-29, Service bulletin: STRUCTURE:BODY. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS \(Federal Motor Vehicle Safety Standards\) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” \(metal plate or vinyl label\) is attached to the instrument panel or body on the driver side at the base of the windshield \(see Figure 1\). · The “Certification Label” \(vinyl adhesive label\) is located on the lower area of the driver side B\-Pillar \(see Figure 1\).
- [NTB03\-074Q](/bulletins/10235698.md), 2023-05-05, Service bulletin: EXTERIOR LIGHTING. HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- [NTB13\-028H](/bulletins/10232658.md), 2023-03-07, Service bulletin: VISIBILITY; STRUCTURE. REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- [NTB09\-081J](/bulletins/10232656.md), 2023-03-07, Service bulletin: VISIBILITY; STRUCTURE. WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- [NTB10\-117A](/bulletins/10200011.md), 2021-08-06, Service bulletin: STRUCTURE; EQUIPMENT. VOLUNTARY SERVICE CAMPAIGN 2008 \- 2009 ROGUE; FRONT DOOR EXTERIOR HANDLE Service Campaign ID \# P0376 is no longer active. • Repair orders opened after this bulletin’s published date are no longer eligible for reimbursement under Campaign ID \# P0376. • Discard all previous versions of NTB10\-117.
- [NTB15113A](/bulletins/10192830.md), 2021-05-10, Service bulletin: ELECTRICAL SYSTEM; ENGINE; EXTERIOR LIGHTING:BRAKE LIGHTS. IF YOU CONFIRM The following, or the customer reports the following: \- Intermittently there is low power when accelerating, And/or \- The stop lamps \(brake lights\) stay ON after releasing the brake pedal, with the ignition ON or OFF. ACTION \- Delete the stop lamp relay and bypass the stop lamp relay circuit. \- Replace the stop lamp switch with the one listed in PARTS INFORMATION. See this bulletin for further detail.
- [NTB03074J](/bulletins/10192750.md), 2021-05-10, Service bulletin: EXTERIOR LIGHTING. SERVICE INFORMATION Occasionally customers may notice water vapor or fog in the headlamps. The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Nissan?s new vehicle limited warranty does not cover physically damaged \(cracked or broken\) headlamps. All current headlamp assemblies are vented to the atmosphere \(not sealed\). \- This is necessary to allow for expansion and contraction of air from temperature "variations" \(warmer or colder\) without damage to the headlamp. \- Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. \- Certain environmental conditions may cause moisture to condense. \- The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.
- [NTB15062A](/bulletins/10192656.md), 2021-05-10, Service bulletin: STRUCTURE; BACK OVER PREVENTION; EQUIPMENT; SUSPENSION; ELECTRICAL SYSTEM. IF YOU CONFIRM There is a popping noise from either the right or the left front coil springs when turning to the right or left. NOTE: Electronic chassis ears may be helpful in isolating this type of noise. ACTION Replace both front coil springs, strut mount bearings, and all other parts listed under PARTS INFORMATION. Position the coil springs as shown on pages 2\-5. Check the front end alignment, adjust to factory specifications as needed. NOTE: Refer to the Electronic Service Manual \(ESM\), section FSU Front Suspension, for strut coil spring removal, installation, and alignment information. IMPORTANT: The Coil Spring Installation Guidelines section in this bulletin MUST be followed in order for a correct repair to be performed.
- [NTB15070](/bulletins/10192617.md), 2021-05-10, Service bulletin: STRUCTURE. IF YOU CONFIRM An oil leak from the Adapter Case Oil Seal or the O\-ring \(see Figure 1\). ACTION NOTE: DO NOT replace the Transfer Case for a leak from the Adapter Case Oil Seal or the O\-ring. Reseal the Adapter Case with the seals listed in PARTS INFORMATION and shown in Figure 1. \* Please see this bulletin for further details.

JSON: [/v1/bulletins/10118713](/v1/bulletins/10118713)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%20NTB17-108&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F10118713&vehicle=Service%20bulletin%20NTB17-108)