# Service bulletin 06\-00\-89\-026L A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned. - Type: Service bulletin - NHTSA id: 10113502 - Published by NHTSA: 2017\-08\-15 - Manufacturer's number: 06\-00\-89\-026L - Manufacturer's date: 2013\-08\-26 - NHTSA component: SERVICE BRAKES; EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER; POWER TRAIN:AXLE ASSEMBLY; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM ## NHTSA's summary This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. ## The document - [NHTSA's copy of the document (PDF)](https://static.nhtsa.gov/odi/tsbs/2013/MC-10113502-9999.pdf) - [If that address does not open, try this one](https://static.nhtsa.gov/odi/tsbs/2013/MC-10113502-0001.pdf) The document is the manufacturer's. This site does not hold it. ## Components Brakes, Electrical system, Engine, Equipment and accessories, Exhaust and emissions, Heating and air conditioning, Transmission and driveline, Axle ## Vehicles listed - 2005 BUICK CENTURY - 2008 to 2014 BUICK ENCLAVE - 2013 to 2014 BUICK ENCORE - 2005 to 2014 BUICK LACROSSE - 2005 BUICK LESABRE - 2006 BUICK LESABRE - 2006 to 2011 BUICK LUCERNE - 2012 BUICK LUCERNE - 2005 BUICK PARK AVENUE - 2005 to 2007 BUICK RAINIER - 2005 BUICK REGAL - 2011 to 2014 BUICK REGAL - 2005 to 2007 BUICK RENDEZVOUS - 2005 to 2007 BUICK TERRAZA - 2008 BUICK TERRAZA - 2012 to 2014 BUICK VERANO - 2013 to 2014 CADILLAC ATS - 2005 to 2014 CADILLAC CTS - 2005 CADILLAC DEVILLE - 2006 to 2011 CADILLAC DTS - 2014 CADILLAC ELR - 2005 to 2014 CADILLAC ESCALADE - 2005 to 2014 CADILLAC ESCALADE ESV - 2005 to 2013 CADILLAC ESCALADE EXT - 2005 to 2014 CADILLAC SRX - 2005 to 2011 CADILLAC STS - 2005 to 2009 CADILLAC XLR - 2013 to 2014 CADILLAC XTS - 2005 CHEVROLET ASTRO - 2005 to 2013 CHEVROLET AVALANCHE - 2005 to 2011 CHEVROLET AVEO - 2005 CHEVROLET BLAZER - 2010 to 2014 CHEVROLET CAMARO - 2012 to 2014 CHEVROLET CAPRICE POLICE PURSUIT - 2013 to 2014 CHEVROLET CAPTIVA - 2005 CHEVROLET CAVALIER - 2014 CHEVROLET CHEVEROLET SS - 2005 CHEVROLET CLASSIC - 2005 to 2010 CHEVROLET COBALT - 2005 to 2012 CHEVROLET COLORADO - 2005 to 2014 CHEVROLET CORVETTE - 2011 to 2014 CHEVROLET CRUZE - 2005 to 2014 CHEVROLET EQUINOX - 2005 to 2014 CHEVROLET EXPRESS - 2006 to 2011 CHEVROLET HHR - 2005 to 2014 CHEVROLET IMPALA - 2005 to 2009 CHEVROLET KODIAK - 2005 to 2014 CHEVROLET MALIBU - 2005 to 2007 CHEVROLET MONTE CARLO - 2013 to 2014 CHEVROLET ORLANDO - 2007 to 2013 CHEVROLET SILVERADO - 2006 to 2007 CHEVROLET SILVERADO 1500 - 2014 CHEVROLET SILVERADO 1500 - 2014 CHEVROLET SILVERADO 2500 - 2012 to 2014 CHEVROLET SONIC - 2013 to 2014 CHEVROLET SPARK - 2014 CHEVROLET SPARK EV - 2005 to 2006 CHEVROLET SSR - 2005 to 2014 CHEVROLET SUBURBAN - 2005 to 2014 CHEVROLET TAHOE - 2005 to 2009 CHEVROLET TRAILBLAZER - 2009 to 2014 CHEVROLET TRAVERSE - 2014 CHEVROLET TRAX - 2005 to 2009 CHEVROLET UPLANDER - 2005 CHEVROLET VENTURE - 2011 to 2014 CHEVROLET VOLT - 2007 to 2014 GMC ACADIA - 2005 to 2012 GMC CANYON - 2005 to 2009 GMC ENVOY - 2005 GMC ENVOY XUV - 2005 GMC JIMMY CLASSIC - 2005 GMC SAFARI - 2005 to 2014 GMC SAVANA - 2005 to 2013 GMC SIERRA - 2014 GMC SIERRA 1500 - 2012 GMC SIERRA 2500 - 2005 to 2013 GMC SIERRA DENALI - 2010 to 2014 GMC TERRAIN - 2005 to 2010 GMC TOPKICK - 2005 to 2014 GMC YUKON - 2005 to 2013 GMC YUKON DENALI - 2005 to 2013 GMC YUKON DENALI XL - 2005 to 2011 GMC YUKON XL - 2012 to 2014 GMC YUKON XL - 2005 to 2010 HUMMER H2 - 2006 to 2010 HUMMER H3 - 2005 PONTIAC AZTEK - 2005 PONTIAC BONNEVILLE - 2008 to 2010 PONTIAC G3 - 2007 to 2010 PONTIAC G5 - 2005 to 2010 PONTIAC G6 - 2008 to 2010 PONTIAC G8 - 2005 PONTIAC GRAND AM - 2005 to 2008 PONTIAC GRAND PRIX - 2005 to 2006 PONTIAC GTO - 2005 to 2009 PONTIAC MONTANA - 2005 to 2006 PONTIAC PURSUIT - 2007 to 2009 PONTIAC PURSUIT - 2006 to 2010 PONTIAC SOLSTICE - 2005 PONTIAC SUNFIRE - 2006 to 2009 PONTIAC TORRENT - 2005 to 2010 PONTIAC VIBE - 2005 PONTIAC WAVE - 2005 to 2009 SAAB 9\-7X - 2008 to 2009 SATURN ASTRA - 2007 to 2010 SATURN AURA - 2005 to 2007 SATURN ION - 2005 SATURN L300 - 2007 to 2010 SATURN OUTLOOK - 2005 to 2007 SATURN RELAY - 2008 SATURN RELAY - 2007 to 2010 SATURN SKY - 2005 to 2010 SATURN VUE ## Other bulletins for the same vehicles and component - [PIP5168F](/bulletins/10129067.md), 2018-02-21, Service bulletin: POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published \“Engine Cranks But Does Not Run\” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. - [PI0137E](/bulletins/10126212.md), 2017-12-22, Service bulletin: POWER TRAIN:AXLE ASSEMBLY. This preliminary bulletin provides a procedure to repair the rear axle seals to correct the customers concern of a chatter or moan on low speed turns. - [PIP5097A](/bulletins/10114562.md), 2017-08-15, Service bulletin: POWER TRAIN:AXLE ASSEMBLY. This Preliminary Information communication provides the technician with the following steps to correct a moan noise from the rear axle during cold turning maneuvers. This noise might start to be noticed as the vehicle accumulates over 3000 miles. The technician is to perform the following steps. 1. With original lube in axle, conduct Freeway Speeds for 10 miles to warm up lube. 2. Immediately drain original lube and refill with fresh lube. 3. In parking lot lock steering to the right, and then execute 5 Full Circles at \(5\-10 mph\). 4. . In parking lot lock steering to the left, and then execute 5 Full Circles at \(5\-10 mph\). 5. Perform 4 Figure 8?s at \(5\-10 mph\). 6. Freeway Speeds for 20 miles until operating temperature is achieved. 7. In parking lot lock steering to the right, and then execute 5 Full Circles at \(5\-10 mph\). 8. In parking lot lock steering to the left, and then execute 5 Full Circles at \(5\-10 mph\). 9. Perform 4 Figure 8?s at \(5\-10 mph\). 10. Immediately drain current lube in axle and refill with fresh lube. 11. Perform Steps 3 thru 9 again. 12. Immediately drain current lube in axle and refill with fresh lube. Proceed with steps 2 through 9 two times, for a total of 3 drain and fill procedures. This should only be done for a moan noise from the rear axle during cold start turning maneuvers. During regular maintenance the fluid only needs to be changed one time. - [G\-179736](/bulletins/10114234.md), 2017-08-15, Service bulletin: POWER TRAIN:AXLE ASSEMBLY. 13397 \- Customer Satisfaction. Certain vehicles were built with a 3.73 rear axle ratio instead of a 3.42 ratio. With the incorrect rear axle, the speedometer and odometer will indicate 9% above the true value and the transmission shift points will be set for a 3.42 ratio. Dealers are to install a new rear axle with a 3.42 ratio. GM will extend the vehicle mileage warranty as appropriate for accrued mileage on sold vehicles - [G\-179000](/bulletins/10114230.md), 2017-08-15, Service bulletin: POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT. 13387 \- Service Update. Dealers are to perform a drive audit. A small number of engines may develop a crankshaft bearing noise condition at low mileage. The drive audit must be completed before vehicle delivery \(and in addition to normal pre\-delivery inspection activities\) to identify vehicles with the condition. If the condition is found, dealers are to replace the engine. - [G\-175492](/bulletins/10114207.md), 2017-08-15, Service bulletin: WHEELS:LUGS/NUTS/BOLTS/STUDS; POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT. 11243A \- Customer Satisfaction \(revised expiration date\). On certain 2011 model year Chevrolet Express and GMC Savana vehicles, two of the four bolts that attach the propshaft to the rear axle may not be fastened to the proper specification and may begin to loosen. This would result in an unusual noise and/or vibration. If the bolts continue to loosen and the propshaft separates from the rear axle, the power to the wheels will no longer be delivered. The engine will continue to run and power braking and steering will not be affected. - [G\-169470](/bulletins/10114182.md), 2017-08-15, Service bulletin: ENGINE AND ENGINE COOLING; POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT:SEAL. 12313 \- Special Coverage. The chrome layer on the balance chain pins may wear, allowing the chain to stretch. This would cause an engine noise, and if left untreated, could cause the chain to break, leading to engine damage. In addition, the fuel pump plunger shaft seal may wear and allow fuel to leak into the crankcase, setting P0172 DTC, and illuminating the Malfunction Indicator Light. This can cause engine run\-on and/or the engine to run rough. If this condition occurs within the stated terms, dealers will replace the engine balance chain and fuel pump. - [PI1354C](/bulletins/10113806.md), 2017-08-15, Service bulletin: POWER TRAIN:AXLE ASSEMBLY. This preliminary informational bulletin outlines the recommendations and procedures for diagnosing and repairing vibrations caused by wheel and tire, axle components and/or propeller shafts. - [PI1354B](/bulletins/10113521.md), 2017-08-15, Service bulletin: WHEELS; POWER TRAIN:AXLE ASSEMBLY. This preliminary informational bulletin outlines the recommendations and procedures for diagnosing and repairing vibrations caused by wheel and tire, axle components and/or propeller shafts. - [PI0561A](/bulletins/10113481.md), 2017-08-15, Service bulletin: POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT:SEAL. This preliminary information bulletin provides a procedure for replacing the right and left axle shaft seals to eliminate a squeak or chirp noise due to the lack of lubrication. JSON: [/v1/bulletins/10113502](/v1/bulletins/10113502) [Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%2006-00-89-026L&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F10113502&vehicle=Service%20bulletin%2006-00-89-026L)