# Service bulletin T\-SB\-0007\-15

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 10111355
- Published by NHTSA: 2017\-08\-14
- Manufacturer's number: T\-SB\-0007\-15
- Manufacturer's date: 2015\-02\-06
- NHTSA component: BACK OVER PREVENTION; EQUIPMENT:ELECTRICAL

## NHTSA's summary

TSB: Some 2015 model year Sienna vehicles equipped with the Intuitive Parking Assist system may exhibit a condition where the Parking Assist customizable settings cannot be changed through the radio display. An updated Clearance Warning Computer is available to address this condition.

## The document

- [NHTSA's copy of the document (PDF)](https://static.nhtsa.gov/odi/tsbs/2015/MC-10111355-9999.pdf)
- [If that address does not open, try this one](https://static.nhtsa.gov/odi/tsbs/2015/MC-10111355-0001.pdf)

The document is the manufacturer's. This site does not hold it.

## Components

Driver assistance, Equipment and accessories, Backup camera

## Vehicles listed

- 2015 TOYOTA SIENNA

## Other bulletins for the same vehicles and component

- [TTT063620](/bulletins/10214323.md), 2022-06-21, Service bulletin: BACK OVER PREVENTION; SERVICE BRAKES, HYDRAULIC. TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care \(TCMC\) brake pads may exhibit a groan or squeak noise in various driving conditions
- [T\-SB\-0088\-21](/bulletins/10203533.md), 2021-11-15, Service bulletin: FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: RADAR; BACK OVER PREVENTION: SENSING SYSTEM: RADAR. TSB: For proper calibration of the millimeter wave radar sensor, the vehicle and radar target must be on a level surface with a consistent plane. If a level surface with a consistent plane is not available, use the Floor Slope Compensation Procedure in this service bulletin in conjunction with the appropriate model and model year Repair Manual instructions when adjusting the millimeter wave radar sensor.
- [T\-TT\-0636\-20 Rev](/bulletins/10190453.md), 2021-04-19, Service bulletin: BACK OVER PREVENTION; SERVICE BRAKES. TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care \(TCMC\) brake pads may exhibit a groan or squeak noise in various driving conditions.
- [T\-TT\-0636\-20](/bulletins/10187241.md), 2021-02-16, Service bulletin: BACK OVER PREVENTION; SERVICE BRAKES. TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care \(TCMC\) brake pads may exhibit a groan or squeak noise in various driving conditions.
- [T\-TT\-0603\-20](/bulletins/10173988.md), 2020-04-20, Service bulletin: BACK OVER PREVENTION; EQUIPMENT. TT: For proper calibration of the millimeter wave radar sensor, the vehicle must be on a level surface. If a level surface is not available, this tech tip should be used in conjunction with the repair manual to set the angle of the front millimeter wave radar sensor and reflector height before performing beam axis adjustment.
- [T\-TT\-0010\-10 Rev](/bulletins/10132812.md), 2018-04-02, Service bulletin: BACK OVER PREVENTION; ENGINE. Tech Tip: Low battery voltage can contribute to a MIL "ON" condition for P0335 \(Crankshaft Position Sensor Circuit\) and/or P0340 \(Camshaft Position Sensor Circuit\) due to inconsistent rotational speed of the engine's crankshaft.

JSON: [/v1/bulletins/10111355](/v1/bulletins/10111355)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%20T-SB-0007-15&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F10111355&vehicle=Service%20bulletin%20T-SB-0007-15)