# Service bulletin SA\-053\-17

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 10111029
- Published by NHTSA: 2017\-08\-10
- Manufacturer's number: SA\-053\-17
- Manufacturer's date: 2017\-07\-06
- NHTSA component: LANE DEPARTURE

## NHTSA's summary

Lane Departure Warning System \(LDWS\) frequently asked questions \(FAQ\)

## The document

- [NHTSA's copy of the document (PDF)](https://static.nhtsa.gov/odi/tsbs/2017/MC-10111029-9999.pdf)
- [If that address does not open, try this one](https://static.nhtsa.gov/odi/tsbs/2017/MC-10111029-0001.pdf)

The document is the manufacturer's. This site does not hold it.

## Components

Driver assistance

## Vehicles listed

- 2016 to 2018 MAZDA CX\-3
- 2016 to 2018 MAZDA CX\-5
- 2016 to 2017 MAZDA CX\-9
- 2014 to 2018 MAZDA MAZDA3
- 2014 to 2017 MAZDA MAZDA6

## Recalls for the same vehicles and component

- [23V487000](/recalls/nhtsa/23V487000.md), 2023-07-14: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA

## Other bulletins for the same vehicles and component

- [09\-005\-26](/bulletins/11028099.md), 2026-02-03, Service bulletin: LANE DEPARTURE: BLIND SPOT DETECTION; ELECTRICAL SYSTEM. If the right\-side Blind Spot Monitoring \(BSM\) control module is replaced for any reason, it is also necessary to replace the left\-side BSM control module in order to complete the radar aiming procedure. If the right\-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. In most cases, if the left\-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" can be completed without any problem \(See CAUTION below for more details\). Other possible symptoms that may be found if the right\-side BSM module is replaced alone: BSM aiming fails “BSM OFF" indicator ON Center Display warning message BSM failsafe \(No operation\) DTC U3000:54 stored in memory DTC U1A4B:54 stored in memory \(CX\-3, MX\-5 only\) NOTE: Since a new BSM control module does not retain the vehicle specification information, it is necessary to acquire and store the vehicle specification information transmitted via CAN communication from the combination meter through automatic configuration after replacement.
- [09\-032\-23](/bulletins/10243551.md), 2023-10-05, Service bulletin: EQUIPMENT ADAPTIVE/MOBILITY; BACK OVER PREVENTION. SERVICE BULLETIN 09\-031/20 ISSUED ON 09/21/20 IS NO LONGER VALID. IT IS SUPERCEDED BY RECALL 6023G \(“2014\-2018 MAZDA3 AND 2016\-2021 CX\-3 \- REARVIEW IMAGE MAY NOT DISPLAY PROPERLY”\).
- [00\-001\-23](/bulletins/10240366.md), 2023-08-03, Service bulletin: ELECTRICAL SYSTEM; VISIBILITY; LANE DEPARTURE. In support of the new Mazda MX\-5 and CX\-3, Mazda will make available for loan on an “as\-needed” basis, a Special Service Tool \(SST\) to allow for the radar aiming of the blind spot monitoring \(BSM\) system. The BSM radar aiming is performed whenever the BSM control module, the BSM bracket or the rear bumper is replaced.
- [08\-001\-23](/bulletins/10232279.md), 2023-03-03, Service bulletin: SEAT BELTS; SEAT BELTS:STATUS INDICATOR SWITCH; FORWARD COLLISION AVOIDANCE; ELECTRICAL SYSTEM; SEATS. Some vehicles may turn on the passenger seatbelt reminder, even though there is no passenger seated in the vehicle. This concern may be caused by the passenger sensor being too sensitive. To eliminate this concern, the passenger sensor has been modified.
- [Issues](/bulletins/10213461.md), 2022-06-06, Service bulletin: BACK OVER PREVENTION:DISPLAY FUNCTION. Active driving display caution \(Update\)
- [1500115](/bulletins/10213460.md), 2022-06-06, Service bulletin: AIR BAGS; LANE DEPARTURE. LDWS or ALH warning light on with DTC C1001:92
- [1500116](/bulletins/10213448.md), 2022-06-06, Service bulletin: AIR BAGS; LANE DEPARTURE. LDWS or ALH warning light on with DTC C1001:92
- [Mil](/bulletins/10213447.md), 2022-06-06, Service bulletin: SERVICE BRAKES; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION. MIL ON WITH DTC PO451 AND/OR PO12A Some customer s may complain about a MIL ON with DTC P0451 \(Fuel tank pressure sensorL sensor characteristic malfunction\) and/or P013A \(HO2S: Slow response \(during transition from rich to lean\)\) Recall 8615J repair procedure may correct this concern
- [System](/bulletins/10213445.md), 2022-06-06, Service bulletin: LANE DEPARTURE: BLIND SPOT DETECTION. Blind spot monitoring \(BSM\) system change
- [0901316](/bulletins/10213430.md), 2022-06-06, Service bulletin: ELECTRICAL SYSTEM:ADAS:BLINDSPOT:WARNING:LAMP. Excessive condensation or water within the headlamp assembly caustion

JSON: [/v1/bulletins/10111029](/v1/bulletins/10111029)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%20SA-053-17&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F10111029&vehicle=Service%20bulletin%20SA-053-17)