Service bulletin SSM 46337

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10095207
Published by NHTSA	2017-03-15
Manufacturer's number	SSM 46337
Manufacturer's date	2017-01-27
NHTSA component	ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)

NHTSA's summary

SOME 2016-2017 FOCUS RS VEHICLES MAY EXHIBIT A MESSAGE DISPLAYED IN THE INSTRUMENT PANEL CLUSTER (IPC) THAT STATES DRIVE MODE SELECTION NOT POSSIBLE. DIAGNOSTIC TROUBLE CODE (DTC) P26FE MAY ALSO BE PRESENT IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. DTC P26FE IS SET WHEN THE PCM IS UNABLE TO COMMAND THE TAILPIPE ACTUATOR TO MOVE. THIS CONCERN MAY BE CAUSED BY LOW TEMPERATURES (BELOW FREEZING) WHEN STARTING THE ENGINE. AFTER ABOUT 180 SECONDS, AND A KEY CYCLE, THE SYSTEM WORKS AS DESIGNED. THE ISSUE IS CURRENTLY UNDER ENGINEERING INVESTIGATION, DO NOT ATTEMPT ANY REPAIRS AT THIS TIME. MONITOR OASIS FOR FUTURE UPDATES. FOR ADDITIONAL TAILPIPE ACTUATOR INFORMATION REFER TO WORKSHOP MANUAL (WSM), SECTION 309-00.

The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

Components

Electrical system, Transmission and driveline, Automatic transmission, Instrument cluster, Transmission control module

Trouble codes named

P26FE

Vehicles listed
FORD FOCUS	2016, 2017

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
14M02 06	2022-12-02. Service bulletin. Certain 2011 through 2015 Model Year Fiesta and 2012 through 2016 Model Year Focus Vehicles Equipped with a DPS6 Automatic Transmission; Transmission Control Module Extended Warranty Coverage REASON FOR THIS SUPPLEMENT Non-Ford Part Usage: • Vehicles that are still covered by the 8 years/80,000-mile Emissions warranty coverage MUST be serviced with a NEW Ford Motor Company TCM. • Vehicles outside of or exceeding the 8 years/80,000-mile coverage are authorized to use a used Ford Motor Company TCM, a refurbished original Ford TCM, or an aftermarket TCM that will successfully complete the required Ford software updates.
SSM 49821	2021-06-01. Service bulletin. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 49798	2021-06-01. Service bulletin. 2015-2018 Focus service parts transmissions part # F1FP-7000-VB / F1FZ-7000-P built on 1-Aug-2020 and through 01-Mar-2021 may have an incorrect input speed sensor A (ISSA) shim thickness. This may cause an intermittent input speed sensor diagnostic trouble code (DTC). In the event of shift issues or skip shift events, check and verify that the ISSA speed sensor shim is 2.0 mm (0.079 in) F1FZ-7Z101-A before proceeding with further diagnostics.
20B23-S1	2020-09-02. Service bulletin. In some of the affected vehicles, customer may report erratic shifting, missed gear shifting, vibration, and check engine light illumination with one or more of the following codes P0809, P0805, P087A, P087B, P0806, P0900, or P090D, due to the clutch actuator motor failure.
SSM 47004	2018-06-11. Service bulletin. Some 2016-2018 Model Year Focus RS may exhibit inaccurate Outside Air Temperature(OAT) readings with intermittent Air Conditioning(A/C) function. Instrument cluster will display 0 degrees F(-18 degrees C) until the vehicle is driven above 20-30 mph for minimum of 1 minute. Concern can occur when engine is running(Key On Engine Running-KOER) and ignition is cycled Off and On again within 1 second. Do not replace Powertrain Control Module(PCM) or ambient air temperature sensor for concern. Sensor is contained within the right hand outside mirror, and is not serviceable separately . Engineering is currently investigating. To assist with the investigation use Report A Vehicle Concern link at the bottom of the Oasis report and submit a Global Concern Report (GCR). Continue to monitor OASIS for future updates.
SSM 47170	2018-05-21. Service bulletin. Some vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 47130	2018-05-21. Service bulletin. Some 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2018 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the Delphi 120 volt electric vehicle service equipment (EVSE) charge cord. To identify a Delphi EVSE the coupler on the EVSE that connects to the vehicle charge port is solid black. For information on the Delphi EVSE indicator status used for diagnostics, reference High Voltage Battery > Charging the High Voltage Battery in the Owners Guide for a 2018 Fusion Energi. Reference the Convenience Cord Light Emitting Diode (LED) Indicators chart. The Workshop Manual (WSM) is scheduled to be revised at a later date.
SSM 46900	2018-01-29. Service bulletin. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
tsb17-2217	2017-12-14. Service bulletin. Some 2016-2017 Focus RS vehicles built on or before 02-Aug-2017 may exhibit an Unable to Change Drive Mode message in the instrument panel cluster (IPC) and/or an illuminated malfunction indicator lamp (MIL) with DTC P26FE stored in the powertrain control module (PCM) memory. Reprogram the PCM to the latest calibration using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 106.04 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
SSM 46068	2017-08-01. Service bulletin. Some Focus Vehicles built on or after 21-Jul-2016 thru 15-Sep-2016 equipped with the DPS6 Transmission exhibiting concerns of shift quality may have an incorrectly aligned clutch actuator spring retainer (7515). While performing transmission or clutch repair on vehicles within these date ranges please Refer to Works Shop Manual (WSM) 307-01A Removal and Installation, Clutch Actuator for proper installation and alignment of these Spring Retainers.