# Service bulletin PIT\-4713\-A

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 10078931
- Published by NHTSA: 2016\-08\-26
- Manufacturer's number: PIT\-4713\-A
- Manufacturer's date: 2016\-05\-18
- NHTSA component: ELECTRICAL SYSTEM:WIRING; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL

## NHTSA's summary

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN HOW TO DIAGNOSE AND REPAIR VEHICLE THAT MAY HAVE A RATTLE, ITCH OR TAPPING NOISE COMING FROM THE CENTER OF THE INSTRUMENT PANEL AREA WHILE DRIVING. THE CAUSE MAY BE AN ENGINE WIRING HARNESS MAKING CONTACT WITH A DOWEL PIN ON THE FORWARD BULKHEAD. TECHNICIAN WILL REMOVE THE ENGINE COVER AND LOCATE THE ENGINE HARNESS. INSPECT FOR A HOLDING CLIP THAT SECURES THE ENGINE HARNESS TO THE FUEL LINE BRACKET. TECHNICIAN WILL INSTALL A HOLDING CLIP TO REMOVE THE SLACK IN THE HARNESS.

## The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

## Components

Electrical system, Instrument cluster, Wiring and fuses

## Vehicles listed

- 2009 CADILLAC ESCALADE HYBRID
- 2008 to 2009 CHEVROLET TAHOE HYBRID
- 2008 to 2009 GMC YUKON HYBRID

## Other bulletins for the same vehicles and component

- [PIT5208](/bulletins/10247765.md), 2023-12-26, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:FUEL GAUGE. Fuel Gauge Shows Empty After Refueling And DTC P2636.
- [PIT5195B](/bulletins/10247748.md), 2023-12-26, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER. Speedometer Needle Accuracy Information.
- [PIT5195](/bulletins/10247747.md), 2023-12-26, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER. Speedometer Needle Accuracy Information
- [PIT5208](/bulletins/10247110.md), 2023-12-11, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:FUEL GAUGE. Fuel Gauge Shows Empty After Refueling And DTC P2636.
- [PIT5195B](/bulletins/10247093.md), 2023-12-11, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER. Speedometer Needle Accuracy Information.
- [PIT5195](/bulletins/10247092.md), 2023-12-11, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER. Speedometer Needle Accuracy Information
- [130089008](/bulletins/10246630.md), 2023-12-11, Service bulletin: ELECTRICAL SYSTEM:WIRING. GM Wiring Repair Strategy Information
- [07\-08\-49\-020R](/bulletins/10244214.md), 2023-10-18, Service bulletin: ELECTRICAL SYSTEM; EQUIPMENT; ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER. This informational bulletin provides information for the IPC odometer programming method quick reference guide.
- [PIT5195G](/bulletins/10213796.md), 2022-06-13, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER. This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is \+/\- 2 MPH at any given speed when looking straight at the needle.
- [07\-08\-49\-020J](/bulletins/10190504.md), 2021-04-20, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system \(SPS\). 2. Odometer setup at the electronic service center \(ESC\) when using an exchange IPC/DIC. 3. Tech 2® – The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. \*The odometer programming is integrated as part of the BCM programming procedure. It is not a stand\-alone event.

JSON: [/v1/bulletins/10078931](/v1/bulletins/10078931)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%20PIT-4713-A&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F10078931&vehicle=Service%20bulletin%20PIT-4713-A)