WenmarOpen by Wenmar Pro

Service bulletin 16U11

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10076525
Published by NHTSA2016-07-14
Manufacturer's number16U11
Manufacturer's date2016-04-19
NHTSA componentEQUIPMENT; ENGINE AND ENGINE COOLING

NHTSA's summary

In some of the affected vehicles, the engine coolant to water concentration may be less than specification. Low coolant concentration could result in reduced cooling system freeze protection, reduced corrosion resistance, heater and radiator performance degradation, and water pump noise or leaks.

The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

Components

Engine, Equipment and accessories

Vehicles listed
FORD F-1502016
FORD TRANSIT2016

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
20V0980002020-02-21. ENGINE; EQUIPMENT:ELECTRICAL
19V2780002019-04-08. ENGINE; EQUIPMENT:ELECTRICAL
19V2710002019-04-03. EQUIPMENT ADAPTIVE/MOBILITY
19V1830002019-03-06. EQUIPMENT ADAPTIVE/MOBILITY
18V8940002018-12-18. ENGINE
16V6180002016-08-24. FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:ENGINE:DIESEL
20160892016-02-22. Accessories

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SSM 550982026-08-25. Service bulletin. Some 2013-2016 Super Duty vehicles equipped with a 6.7L diesel engine and 2015-2019 Transit vehicles equipped with a 3.2L diesel engine may not pass a state smog test due to the exhaust gas system (EGS) monitor that will not run after completing the exhaust gas sensor drive cycle located within Section 2 of the Powertrain Control/Emissions Diagnostics (PC/ED) Manual > Drive Cycles. This may be due to the vehicles diesel oxidation catalyst (DOC) age counter being under the 120-minute age requirement. There is an all-new "PCM Catalytic Converter Age Evaluation" application within the latest version of the Ford Diagnosis and Repair System (FDRS). Use this new FDRS application to determine the age (in minutes) of the DOC. If the age is less than 120 minutes, perform manual regenerations to increase the catalyst age counter to satisfy the monitor age requirement. If further assistance is needed, contact the technical assistance center (TAC). Note: this article only applies to the EGS monitor. Problems with other vehicle monitors not running successfully must be addressed using normal diagnostics located i
SSM 546902026-04-06. Service bulletin. Some 2013-2016 Super Duty vehicles equipped with a 6.7L diesel engine and 2015-2019 Transit vehicles equipped with a 3.2L diesel engine may not pass a state smog test due to the exhaust gas system (EGS) monitor that will not run after completing the Exhaust Gas Sensor drive cycle located within Section 2 of the Powertrain Control/Emissions Diagnostics (PC/ED) Manual > Drive Cycles. This may be due to the vehicles diesel oxidation catalyst (DOC) age counter being under the 120-minute requirement. Engineering is investigating this issue and working on a solution.
SSM 524762024-05-03. Service bulletin. All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
TSB 24-20982024-04-04. Service bulletin. This article supersedes TSB 23-2330 to update the Parts List. Some 2015-2017 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit an oil leak from the oil pan RTV seal. This may be due to various concerns with the oil pan. To correct the condition, follow the Service Procedure to replace the oil pan with the later style oil pan.
SSM 523352024-03-20. Service bulletin. For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 523342024-03-20. Service bulletin. Some 2011-2024 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a tick tap and/or typewriter ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150°F (65°C) or higher and engine speed is at idle up to approximately 1700 RPM. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise tick rate can be faster or slower and is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted. This information along with an example audio clip has been added to the WSM Section 303-00 Engine System General Information > Diagnosis and Testing > Engine > PPT F > Step F2.
TSB 23-23302024-03-07. Service bulletin. This article supersedes TSB 23-2083 to update the Service Procedure and the Part List. Some 2015-2017 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit an oil leak from the oil pan RTV seal. This may be due to various concerns with the oil pan. To correct the condition, follow the Service Procedure to replace the oil pan with the later style oil pan.
23N042024-03-05. Service bulletin. Certain 2015-2019 Model Year Transit Vehicles Equipped With 3.2L Diesel Engine - Exhaust Gas Temperature (EGT) Sensor Replacement
SSM 519622023-11-03. Service bulletin. Some 2016-2018 F-150 and 2016-2017 Expedition/Navigator vehicles may require pressure bleeding of the brake system. The brake system pressure bleeding procedure in the Workshop Manual (WSM), Section 206-00, has been updated to add a warning to not apply the brake pedal or master cylinder damage may occur.
SSM 519472023-10-06. Service bulletin. Some 2015-2019 F-Super Duty and 2015-2020 F-150/Mustang vehicles may require replacement of the powertrain control module (PCM) for various reasons. While performing a programmable module installation (PMI) using the Integrated Diagnostic Service (IDS) scan tool, an error message may state: Configuration Failed, Would You Like To Retry? This may be due to improper module replacement steps. Make sure that the original module is installed in the vehicle, delete the vehicle session, then start a new vehicle session. Once the session starts, run the PCM PMI and install the new PCM only when the scan tool instructs. Finish the PMI by following the prompts given by IDS. If the original PCM is not available, it is possible to configure the module by running as-built programming on the PCM. When IDS asks to obtain part numbers or configuration data, select configuration data.