Service bulletin PIP5204A
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10070508 |
| Published by NHTSA | 2016-06-13 |
| Manufacturer's number | PIP5204A |
| Manufacturer's date | 2014-09-01 |
| NHTSA component | ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:DIESEL |
NHTSA's summary
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
The document
No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.
Components
Engine, Exhaust and emissions, Catalytic converter
| CHEVROLET EXPRESS | 2010, 2011, 2012, 2013, 2014, 2015 |
|---|---|
| CHEVROLET SILVERADO 1500 | 2010, 2011, 2012, 2013, 2014, 2015 (the catalog's model; the bulletin names a series or trim of it) |
| GMC SAVANA | 2010, 2011, 2012, 2013, 2014, 2015 |
| GMC SIERRA 1500 | 2010, 2011, 2012, 2013, 2014, 2015 (the catalog's model; the bulletin names a series or trim of it) |
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 14096A | 2023-12-18. Service bulletin. Oxygen Sensor Fracture |
|---|---|
| 14096 | 2023-12-18. Service bulletin. Oxygen Sensor Fracture |
| PIP3119P | 2019-04-08. Service bulletin. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. |
| 060601010D | 2018-06-04. Service bulletin. This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system. |
| PIP5232A | 2018-05-07. Service bulletin. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIP5232 | 2018-05-07. Service bulletin. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIP5232B | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIP5228B | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that have a vibration that is felt between 1200 ? 1400 engine revolutions per minute when in active fuel management V4 mode. Technician will need to use J?38792-A Electronic Vibration Analyzer 2 or CH?51450-NVH Pico Oscilloscope Diagnostic Kit to measure the frequency of the vibration. Technician will need to remove and replace the exhaust muffler clamp that joins the three-way catalytic converter assembly to the pipe of the muffler assembly. After the exhaust is reinstalled remove and reinstall each cab mounts and retest. |
| PIP5232C | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIP3119N | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. |