Service bulletin PIP5097
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10063238 |
| Published by NHTSA | 2016-04-26 |
| Manufacturer's number | PIP5097 |
| Manufacturer's date | 2013-03-01 |
| NHTSA component | POWER TRAIN:AXLE ASSEMBLY |
NHTSA's summary
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
The document
No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.
Components
Transmission and driveline, Axle
| CHEVROLET CAMARO | 2012, 2013 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| PIP5168F | 2018-02-21. Service bulletin. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. |
|---|---|
| PI0137E | 2017-12-22. Service bulletin. This preliminary bulletin provides a procedure to repair the rear axle seals to correct the customers concern of a chatter or moan on low speed turns. |
| PIP5097A | 2017-08-15. Service bulletin. This Preliminary Information communication provides the technician with the following steps to correct a moan noise from the rear axle during cold turning maneuvers. This noise might start to be noticed as the vehicle accumulates over 3000 miles. The technician is to perform the following steps. 1. With original lube in axle, conduct Freeway Speeds for 10 miles to warm up lube. 2. Immediately drain original lube and refill with fresh lube. 3. In parking lot lock steering to the right, and then execute 5 Full Circles at (5-10 mph). 4. . In parking lot lock steering to the left, and then execute 5 Full Circles at (5-10 mph). 5. Perform 4 Figure 8?s at (5-10 mph). 6. Freeway Speeds for 20 miles until operating temperature is achieved. 7. In parking lot lock steering to the right, and then execute 5 Full Circles at (5-10 mph). 8. In parking lot lock steering to the left, and then execute 5 Full Circles at (5-10 mph). 9. Perform 4 Figure 8?s at (5-10 mph). 10. Immediately drain current lube in axle and refill with fresh lube. 11. Perform Steps 3 thru 9 again. 12. Immediately drain current lube in axle and refill with fresh lube. Proceed with steps 2 through 9 two times, for a total of 3 drain and fill procedures. This should only be done for a moan noise from the rear axle during cold start turning maneuvers. During regular maintenance the fluid only needs to be changed one time. |
| 06-00-89-026L | 2017-08-15. Service bulletin. This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. |
| PIP5102 | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P0016 stored. Technician will need to inspect the reluctor on the crankshaft. If the reluctor has moved replace the crankshaft. |
| PI0137E | 2016-06-02. Service bulletin. SUMMARY TO BE PROVIDED ON A FUTURE DATE. |