# Service bulletin ASI\-44534

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 10056196
- Published by NHTSA: 2014\-10\-01
- Manufacturer's number: ASI\-44534
- Manufacturer's date: 2014\-05\-01
- NHTSA component: POWER TRAIN:AUTOMATIC TRANSMISSION

## NHTSA's summary

FORD: WHEN SHIFTING BETWEEN PARK, REVERSE AND/OR DURING 2\-3 SHIFT, AN INTERMITTENT CLUNK OCCURS WITH A TORQSHIFT TRANSMISSION. MODEL 2003\-2014 F\-SUPER DUTY, E SERIES, EXCURSION, F\-53 MOTORHOME CHASSIS, LOW CAB FORWARD. \*PE

## The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

## Components

Transmission and driveline, Automatic transmission

## Vehicles listed

- 2003 to 2014 FORD E\-150
- 2003 to 2014 FORD E\-250
- 2003 to 2014 FORD E\-350
- 2003 to 2014 FORD E\-450
- 2003 FORD E\-550
- 2004 to 2009 FORD E\-550
- 2003 to 2005 FORD EXCURSION
- 2003 to 2014 FORD F\-250 SD
- 2003 to 2014 FORD F\-350 SD
- 2003 to 2014 FORD F\-450 SD
- 2006 to 2014 FORD F\-53
- 2003 to 2014 FORD F\-550 SD
- 2004 to 2014 FORD F\-650 SD
- 2004 to 2014 FORD F\-750 SD
- 2008 to 2009 FORD LCF 450
- 2006 to 2007 FORD LCF 450 SERIES
- 2008 to 2009 FORD LCF 550
- 2006 to 2007 FORD LCF 550 SERIES

## Recalls for the same vehicles and component

- [15V175000](/recalls/nhtsa/15V175000.md), 2015-03-25: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE \(TCM/PCM/TECM\)
- [11V582000](/recalls/nhtsa/11V582000.md), 2011-12-08: POWER TRAIN:AUTOMATIC TRANSMISSION
- [07V139000](/recalls/nhtsa/07V139000.md), 2007-03-26: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE \(TCM/PCM/TECM\)

## Other bulletins for the same vehicles and component

- [SSM 51909](/bulletins/10243490.md), 2023-10-04, Service bulletin: POWER TRAIN:AUTOMATIC TRANSMISSION. When performing any transmission fluid changes or topoffs involving MERCON SP, MERCON LV has replaced all versions of MERCON SP and can be used going forward. Mixing MERCON LV and MERCON SP in the same transmission is acceptable. After 30\-Jun\-2023, MERCON SP ATF will no longer be manufactured and will only be available until inventory depletes.
- [SSM 51854](/bulletins/10241626.md), 2023-09-04, Service bulletin: POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE \(TCM/PCM/TECM\); POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE \(TCM/PCM/TECM\). Various 2013\-2019 vehicles may exhibit an illuminated malfunction indicator lamp \(MIL\) with diagnostic trouble code \(DTC\) P264F after powertrain control module \(PCM\) replacement. This DTC indicates that the engine serial number \(ESN\) must be programmed into the PCM. The ESN is located on PTS \> Diagnostics tab \> HVBoM \> Features \> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials \(HvBOM\), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab\> powertrain menu\> Service Functions\> ESN.
- [SSM 51849](/bulletins/10241547.md), 2023-09-01, Service bulletin: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE \(TCM/PCM/TECM\). Various 2013\-2019 vehicles may exhibit an illuminated malfunction indicator lamp \(MIL\) with diagnostic trouble code \(DTC\) P264F after powertrain control module \(PCM\) replacement. This DTC indicates that the engine serial number \(ESN\) must be programmed into the PCM. The ESN is located on PTS\> OASIS\> Features\> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials \(HvBOM\), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab\> powertrain menu\> Service Functions\> ESN.
- [SSM 50636](/bulletins/10209384.md), 2022-03-29, Service bulletin: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; ENGINE AND ENGINE COOLING; EQUIPMENT. 2011\-2022 F\-Super Duty and 2016\-2023 F\-650/F\-750 vehicles equipped with a 6.7L engine may exhibit an elevated idle condition. During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26°C \(80°F\) and may increase to 1200 RPM at \-40 °C \(\-40°F\). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take\-off \(PTO\) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.
- [SSM 50096](/bulletins/10201580.md), 2021-09-28, Service bulletin: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE \(TCM/PCM/TECM\); ENGINE AND ENGINE COOLING. Some 2013\-2016 F\-Super Duty vehicles equipped with a 6.7L engine may exhibit an Exhaust System Fluid Fault message and a forced idle mode with various diagnostic trouble codes \(DTC\) stored in the powertrain control module \(PCM\). A video explaining how to remove the vehicle from forced idle mode has been added to the Technical Support Videos under the Technical Assistance tab on PTS. The video can be accessed using the following web link, http://site\-307934.bcvp0rtal.com/detail/videos/303\-\-\-engine/video/6258842975001/2013\-2016\-f\-super\-duty\-exhaust\-fluid\-fault\-procedure.
- [16\-0060](/bulletins/10183761.md), 2020-12-07, Service bulletin: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE. Some 2012\-2016 F\-Super Duty vehicles equipped with a 6.2L or 6.8L engine built on or before 4/6/2016 may exhibit an illuminated malfunction indicator lamp \(MIL\) with DTCs P0627, P025A, P025B and/or U0109 stored in powertrain control module \(PCM\) memory.
- [SSM 47823](/bulletins/10156886.md), 2019-04-08, Service bulletin: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE \(TCM/PCM/TECM\); ENGINE. Various 2013\-2019 vehicles may exhibit an illuminated malfunction indicator lamp \(MIL\) with diagnostic trouble code \(DTC\) P264F after powertrain control module \(PCM\) replacement. This DTC indicates that the engine serial number \(ESN\) must be programmed into the PCM. The ESN is located on PTS\> OASIS\> Features\> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials \(HvBOM\), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab\> powertrain menu\> Service Functions\> ESN.
- [18N04](/bulletins/10148745.md), 2018-11-19, Service bulletin: ENGINE AND ENGINE COOLING:ENGINE:DIESEL; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE \(TCM/PCM/TECM\); ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE \(PCV\). Certain 2014\-2016 Model Year F\-250 ? F\-550 and 2016 Model Year F\-650 \- F\-750 Vehicles, With 6.7L Diesel Engine \- Crankcase Ventilation Oil Separator Assembly. Certain 2018 Model Year F\-150 and 2019 Model Year F\-250 through F\-550 Superduty Vehicles Equipped with a Diesel Engine \- Powertrain Control Module Reprogramming
- [SSM 47597](/bulletins/10148731.md), 2018-11-19, Service bulletin: ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE \(TCM/PCM/TECM\); EQUIPMENT. Some 2013\-2019 F\-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated MIL with only DTC P2074 stored in the powertrain control module \(PCM\). This may be due to a dirty air filter, replace the filter if necessary. Do not replace the PCM or mass air flow \(MAF\) sensor for this concern. Instead perform a MAF parameter reset under: Toolbox \> Powertrain \> Service Functions \> Reset/Clear Specified Function \> Reset/Clear Functions \> MAF Sensor. Engineering is investigating. Monitor OASIS for updates.
- [18U12](/bulletins/10137150.md), 2018-05-21, Service bulletin: POWER TRAIN:AUTOMATIC TRANSMISSION. Certain 2018 Model Year Escape and MKC Vehicles \- Transmission Bell Housing Bolt TorqueCertain 2012\-2016 Model Year F\-450 ? F\-750 and F\-59 Commercial Stripped Chassis Vehicles Equipped with a 6.8L Engine \- Camshaft Roller Follower Replacement

JSON: [/v1/bulletins/10056196](/v1/bulletins/10056196)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%20ASI-44534&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F10056196&vehicle=Service%20bulletin%20ASI-44534)