Service bulletin ASI-32247

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10053406
Published by NHTSA	2013-10-24
Manufacturer's number	ASI-32247
Manufacturer's date	2013-05-01
NHTSA component	POWER TRAIN:AUTOMATIC TRANSMISSION

NHTSA's summary

FORD: ON SOME TRUCKS, THE REPLACEMENT OF (7A100) MAIN CONTROL ASSEMBLY IS NO LONGER NECESSARY WHEN NORMAL DIAGNOSTICS LEAD TO TRANSMISSION SOLENOID REPLACEMENT WHERE A BAND 1 SOLENOID IS USED. MODELS 2011-2013 F-SUPER DUTY TRUCK. *PE

The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

Components

Transmission and driveline, Automatic transmission

Vehicles listed
FORD F-250 SD	2011, 2012, 2013 (the catalog's model; the bulletin names a series or trim of it)
FORD F-350 SD	2011, 2012, 2013 (the catalog's model; the bulletin names a series or trim of it)
FORD F-450 SD	2011, 2012, 2013 (the catalog's model; the bulletin names a series or trim of it)
FORD F-550 SD	2011, 2012, 2013 (the catalog's model; the bulletin names a series or trim of it)
FORD F-650 SD	2011, 2012, 2013 (the catalog's model; the bulletin names a series or trim of it)
FORD F-750 SD	2011, 2012, 2013 (the catalog's model; the bulletin names a series or trim of it)

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
15V175000	2015-03-25. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
11V582000	2011-12-08. POWER TRAIN:AUTOMATIC TRANSMISSION

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SSM 51854	2023-09-04. Service bulletin. Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS > Diagnostics tab > HVBoM > Features > Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
SSM 51849	2023-09-01. Service bulletin. Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
SSM 50636	2022-03-29. Service bulletin. 2011-2022 F-Super Duty and 2016-2023 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an elevated idle condition. During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26°C (80°F) and may increase to 1200 RPM at -40 °C (-40°F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.
SSM 50096	2021-09-28. Service bulletin. Some 2013-2016 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an Exhaust System Fluid Fault message and a forced idle mode with various diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). A video explaining how to remove the vehicle from forced idle mode has been added to the Technical Support Videos under the Technical Assistance tab on PTS. The video can be accessed using the following web link, http://site-307934.bcvp0rtal.com/detail/videos/303---engine/video/6258842975001/2013-2016-f-super-duty-exhaust-fluid-fault-procedure.
16-0060	2020-12-07. Service bulletin. Some 2012-2016 F-Super Duty vehicles equipped with a 6.2L or 6.8L engine built on or before 4/6/2016 may exhibit an illuminated malfunction indicator lamp (MIL) with DTCs P0627, P025A, P025B and/or U0109 stored in powertrain control module (PCM) memory.
SSM 47823	2019-04-08. Service bulletin. Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
SSM 47597	2018-11-19. Service bulletin. Some 2013-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated MIL with only DTC P2074 stored in the powertrain control module (PCM). This may be due to a dirty air filter, replace the filter if necessary. Do not replace the PCM or mass air flow (MAF) sensor for this concern. Instead perform a MAF parameter reset under: Toolbox > Powertrain > Service Functions > Reset/Clear Specified Function > Reset/Clear Functions > MAF Sensor. Engineering is investigating. Monitor OASIS for updates.
18U12	2018-05-21. Service bulletin. Certain 2018 Model Year Escape and MKC Vehicles - Transmission Bell Housing Bolt TorqueCertain 2012-2016 Model Year F-450 ? F-750 and F-59 Commercial Stripped Chassis Vehicles Equipped with a 6.8L Engine - Camshaft Roller Follower Replacement
SSM 46900	2018-01-29. Service bulletin. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
SSM 46066	2017-08-01. Service bulletin. Some 2013-2017 F-Super Duty, 2015-2017 Transit and 2016-2017 F650-F750 vehicles equipped with a diesel engine may exhibit diagnostic trouble code (DTC) P2201 (NOX Sensor Circuit Range/Performance Bank 1 Sensor 1) in the powertrain control module (PCM). When repairing DTC P2201, refer to the online version of the powertrain control/emission diagnostic (PC/ED) manual for the latest diagnostics. The pinpoint test RD and diagnostic trouble code chart have been updated in section 4 and 5 for DTC P2201.