# Service bulletin PIP5038

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 10045342
- Published by NHTSA: 2012\-08\-28
- Manufacturer's number: PIP5038
- Manufacturer's date: 2012\-07\-01
- NHTSA component: ELECTRICAL SYSTEM:IGNITION; ENGINE

## NHTSA's summary

GENERAL MOTORS: SES LIGHT ENGINE MISFIRE AND/OR SHUDDER\- INSPECT IGNITION COILS. THIS MAY BE THE RESULT OF A HEAT STRESSED/DAMAGED IGNITION COIL. \*JS

## The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

## Components

Electrical system, Engine, Ignition

## Vehicles listed

- 2009 BUICK ENCLAVE
- 2008 to 2009 CADILLAC CTS
- 2008 to 2009 CADILLAC STS
- 2009 CHEVROLET TRAVERSE
- 2009 GMC ACADIA
- 2009 SATURN OUTLOOK

## Recalls for the same vehicles and component

- [14V394000](/recalls/nhtsa/14V394000.md), 2014-07-02: ELECTRICAL SYSTEM:IGNITION

## Other bulletins for the same vehicles and component

- [PIT4271E](/bulletins/10247648.md), 2023-12-26, Service bulletin: UNKNOWN OR OTHER; ELECTRICAL SYSTEM:IGNITION. Light Flashes or Stays on Steady During A Remote Start.
- [14172B](/bulletins/10245885.md), 2023-12-04, Service bulletin: ELECTRICAL SYSTEM:IGNITION; ELECTRICAL SYSTEM. Unintended Ignition Key Rotation
- [14172A](/bulletins/10245884.md), 2023-12-04, Service bulletin: ELECTRICAL SYSTEM:IGNITION; ELECTRICAL SYSTEM. Unintended Ignition Key Rotation
- [PIC5650K](/bulletins/10237659.md), 2023-06-13, Service bulletin: POWER TRAIN; ELECTRICAL SYSTEM:IGNITION. This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
- [PIC5236A](/bulletins/10113925.md), 2017-08-15, Service bulletin: EQUIPMENT; ELECTRICAL SYSTEM:IGNITION. This Preliminary Information communication provides information to the technician how to install the new style ignition lock cylinder into the vehicle. When installing the new cylinder it is important to carefully inspect the housing for debris or damage from the old lock cylinder. No tools are required for installing the new lock cylinder. When installing into the housing, ensure that the lock cylinder is fully seated to ensure it latches into position. Do not use the old style lock cylinder that is still used on the manual transmission vehicle on an automatic transmission car.
- [PI1018A](/bulletins/10113519.md), 2017-08-15, Service bulletin: EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:IGNITION. This preliminary informational bulletin adds the 2015 model year to repair information on correcting a customer concern of poor, limited, reduced Remote Keyless Entry \(RKE\) or Remote Vehicle Start \(RVS\) range.
- [PIC5630](/bulletins/10112977.md), 2017-08-15, Service bulletin: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE \(TCM/PCM/TECM\); ELECTRICAL SYSTEM:IGNITION; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, and or an intermittent Service Engine Soon lamp illuminated. Technician should inspect the round connector at the transmission control module for possible High Speed LAN wire or wires that may be pushed out of the back of the connector.
- [PIC5252A](/bulletins/10112651.md), 2017-08-15, Service bulletin: ELECTRICAL SYSTEM:IGNITION. This Preliminary Information communication provides information to the technician with a diagnostic tip on how to remove the ignition lock cylinder. Technician can use a pick tool on the hole behind the land on the lock cylinder housing and pull the ignition lock cylinder out of the ignition.
- [PIC5252A](/bulletins/10071881.md), 2016-06-17, Service bulletin: ELECTRICAL SYSTEM:IGNITION. SUMMARY TO BE PROVIDED ON A FUTURE DATE.
- [SB\-10256](/bulletins/10037828.md), 2011-06-07, Service bulletin: ELECTRICAL SYSTEM:IGNITION:SWITCH; ELECTRICAL SYSTEM:IGNITION. GM: THERE MAY BE A BIND BETWEEN THE IGNITION LOCK AND THE HOUSING MAKING IT UNABLE TO REMOVE THE KEY FROM THE IGNITION. THE DRIVER MAY NOT BE ABLE TO TURN THE VEHICLE OFF IF IT'S RUNNING. \*RM

JSON: [/v1/bulletins/10045342](/v1/bulletins/10045342)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%20PIP5038&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F10045342&vehicle=Service%20bulletin%20PIP5038)