WenmarOpen by Wenmar Pro

Service bulletin POL-09-01

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10032527
Published by NHTSA2010-04-09
Manufacturer's numberPOL-09-01
Manufacturer's date2009-06-04
NHTSA componentSEATS; AIR BAGS:FRONTAL

NHTSA's summary

TOYOTA: NEW SERVICE REPLACEMENT PARTS AVAILABLE FOR FRONT SEAT ASSEMBLY WITH AIRBAG. *PE

The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

Components

Air bags, Seats

Vehicles listed
TOYOTA CAMRY2007
TOYOTA SIENNA2005

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
16V3960002016-06-02. SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER
14V7430002014-11-19. SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER
06V0960002006-04-03. AIR BAGS
20052232005-06-20. Seats And Restraints

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
TSB0032202023-10-16. Service bulletin. TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0094-21 Rev2022-12-19. Service bulletin. TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
Toyota Safety Re2021-04-19. Service bulletin. Toyota Safety Recall and Service Campaign - Technician Certification Requirements
T-TT-0213-132018-04-23. Service bulletin. Toyota vehicles are equipped with SRS, including various airbags and in some models, seat belt pre-tensioners, to help reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pretensioner devices did not perform as expected, please follow the steps in the recommendations section below.
T-SB-0218-17_Rev2018-04-02. Service bulletin. TSB: REVISION NOTICE July 20, 2017 Rev1: Applicability has been updated to exclude 2007 ? 2017 model year Avanza vehicles. Some hazardous material treatment and handling regulations at the state and local level define the pre-disposal deployment of airbag and pre-tensioner assemblies as hazardous material treatment. Hazardous material treatment may require special training, certification or licensing in certain areas. TMS recommends that dealership personnel carefully review and follow ALL local and state regulations, and where necessary, contract with Environmental Protection Agency (EPA) Licensed Hazardous Waste Transportation and Disposal facilities.
T-TT-0092-11 Rev2018-04-02. Service bulletin. Some customers may complain that the Rear Seat Entertainment (RSE) system is inoperative if they have misplaced the parental passcode for the system.
DR8 Reg Ltr2018-04-02. Service bulletin. Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. Please note the following information for Regional and PD associates.
T-SB-0122-11 Rev2018-04-02. Service bulletin. Beginning in 1998, Toyota introduced side airbags as optional equipment. Toyota does NOT recommend replacement of original seat covers with non-Toyota leather or other seat cover materials on vehicles due to the following: Seat covers NOT recommended by Toyota may affect side airbag performance, in general or in part, during an accident. Modifications that negatively affect side airbag performance can result in severe occupant injuries. Seat covers are an integral part of this safety system. Replacing fabric seat covers with non-Toyota leather or other seat cover materials may compromise the effectiveness of this safety system. The design of the seat is complex, integrating safety and strength with comfort and luxury. Toyota strongly discourages modifying original equipment seats that have optional side airbags. Additionally, Toyota strongly advises against the installation or use of aftermarket seat covers, which could impair the performance of the side airbags in the event of an accident.
PE14-001 Camry H2018-04-02. Service bulletin. The National Highway Traffic Safety Administration (NHTSA) has opened an investigation called a Preliminary Evaluation on January 23, 2014. A Preliminary Evaluation is an early-stage inquiry to determine if further analysis (an Engineering Analysis) is warranted; this is not a recall. Toyota will be cooperating fully with the agency in its efforts to investigate the allegations.
Warranty Enhance2018-04-02. Service bulletin. Toyota has received reports regarding excessive electrical resistance in the Side Airbag connector of certain 2004 to 2009 Model Year Sienna vehicles. The connector could have been improperly crimped during the manufacturing process. In certain cases, oxidization buildup in the connector can occur resulting in illumination of the airbag warning lamp.