# Service bulletin 060852002

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 10022925
- Published by NHTSA: 2007\-10\-05
- Manufacturer's number: 060852002
- Manufacturer's date: 2008\-11\-01
- Replaces: SB\-06\-08\-52\-002G
- NHTSA component: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL

## NHTSA's summary

REMOTE KEYLESS ENTRY \(RKE\) INOPERATIVE, POOR RANGE, TIRE PRESSURE MONITOR \(TPM\) MESSAGE DISPLAYED, REMOTE VEHICLE START \(RVS\) \(REPLACE RKE TRANSMITTERS AND REPROGRAM REMOTE CONTROL DOOR LOCK RECEIVER \(RCDLR\). \*NJ UPDATED 5/14/09. \*PE

## The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

## Components

Electrical system, Instrument cluster

## Vehicles listed

- 2007 CADILLAC ESCALADE
- 2007 CHEVROLET AVALANCHE 1500
- 2007 CHEVROLET AVALANCHE 2500
- 2007 CHEVROLET EQUINOX
- 2007 CHEVROLET SUBURBAN 1500
- 2007 CHEVROLET TAHOE
- 2007 GMC YUKON
- 2007 PONTIAC TORRENT

## Other bulletins for the same vehicles and component

- [PIT5208](/bulletins/10247765.md), 2023-12-26, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:FUEL GAUGE. Fuel Gauge Shows Empty After Refueling And DTC P2636.
- [PIT5195B](/bulletins/10247748.md), 2023-12-26, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER. Speedometer Needle Accuracy Information.
- [PIT5195](/bulletins/10247747.md), 2023-12-26, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER. Speedometer Needle Accuracy Information
- [PIT5208](/bulletins/10247110.md), 2023-12-11, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:FUEL GAUGE. Fuel Gauge Shows Empty After Refueling And DTC P2636.
- [PIT5195B](/bulletins/10247093.md), 2023-12-11, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER. Speedometer Needle Accuracy Information.
- [PIT5195](/bulletins/10247092.md), 2023-12-11, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER. Speedometer Needle Accuracy Information
- [130089004H](/bulletins/10246623.md), 2023-12-11, Service bulletin: VISIBILITY:WINDSHIELD; UNKNOWN OR OTHER; ELECTRICAL SYSTEM:SOFTWARE; EXTERIOR LIGHTING:LIGHTING CONTROL MODULE; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; VEHICLE SPEED CONTROL:THROTTLE:THROTTLE POSITION SENSOR \(TPS\). Car and Truck Fix it Right the First Time Issues
- [07\-08\-49\-020R](/bulletins/10244214.md), 2023-10-18, Service bulletin: ELECTRICAL SYSTEM; EQUIPMENT; ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER. This informational bulletin provides information for the IPC odometer programming method quick reference guide.
- [PIT5195G](/bulletins/10213796.md), 2022-06-13, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER. This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is \+/\- 2 MPH at any given speed when looking straight at the needle.
- [07\-08\-49\-020J](/bulletins/10190504.md), 2021-04-20, Service bulletin: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system \(SPS\). 2. Odometer setup at the electronic service center \(ESC\) when using an exchange IPC/DIC. 3. Tech 2® – The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. \*The odometer programming is integrated as part of the BCM programming procedure. It is not a stand\-alone event.

JSON: [/v1/bulletins/10022925](/v1/bulletins/10022925)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%20060852002&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F10022925&vehicle=Service%20bulletin%20060852002)