# Service bulletin 1802406

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

- Type: Service bulletin
- NHTSA id: 10020194
- Published by NHTSA: 2006\-08\-09
- Manufacturer's number: 1802406
- Manufacturer's date: 2006\-07\-21
- NHTSA component: ENGINE AND ENGINE COOLING:ENGINE

## NHTSA's summary

ENGINE CYLINDER MISFIRE OR IGNITION COIL MALFUNCTION DURING HEAVY RAIN OR CAR WASH. \*TT

## The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

## Components

Engine

## Vehicles listed

- 2004 to 2006 DODGE DURANGO

## Other bulletins for the same vehicles and component

- [9003215](/bulletins/10229181.md), 2023-01-09, Service bulletin: ENGINE AND ENGINE COOLING. Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non\-EGR applications. An EGR Block\-Off Plate \(53032739AA\) must be ordered when installing this Long Block Assembly in a Non\-EGR application. Unless, the EGR Block\-Off Plate is being transferred from the old engine.
- [68332810](/bulletins/10223854.md), 2022-10-17, Service bulletin: ENGINE AND ENGINE COOLING. Service \- Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY \- The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T\-joints.\~ 2. Fill the T\-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar® Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2\-mm \[0.063\-in\] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.\~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket\(s\) onto the oil pan flange.\~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2\-mm \[0.063\-in\] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.\~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 N·m \[21 ft. lbs.\].
- [9003215](/bulletins/10223602.md), 2022-10-17, Service bulletin: ENGINE AND ENGINE COOLING. Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non\-EGR applications. An EGR Block\-Off Plate \(53032739AA\) must be ordered when installing this Long Block Assembly in a Non\-EGR application. Unless, the EGR Block\-Off Plate is being transferred from the old engine.
- [9002887](/bulletins/10223599.md), 2022-10-17, Service bulletin: ENGINE AND ENGINE COOLING. Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.\~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.\~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
- [9004350](/bulletins/10220837.md), 2022-09-26, Service bulletin: ENGINE AND ENGINE COOLING; POWER TRAIN. GEAR MOTOR, Transfer Case The gear motor assembly is shipped in AWD/2WD position. The transfer case needs to be positioned in AWD/2WD position to properly assemble gear motor to T\-Case. Please reference Star Online publication S2121000003 for further details. Do not have the transfer case in in another position other than AWD/2WD and rotate the motor to align the bolt holes as this could result in damage to the gear motor.
- [R2118796A](/bulletins/10191460.md), 2021-05-03, Service bulletin: ENGINE AND ENGINE COOLING. Valve Body. These may cause over drive cycling.
- [9004350](/bulletins/10190584.md), 2021-04-26, Service bulletin: ENGINE AND ENGINE COOLING. GEAR MOTOR, Transfer Case The gear motor assembly is shipped in AWD/2WD position. The transfer case needs to be positioned in AWD/2WD position to properly assemble gear motor to T\-Case. Please reference Star Online publication S2121000003 for further details. Do not have the transfer case in in another position other than AWD/2WD and rotate the motor to align the bolt holes as this could result in damage to the gear motor.
- [RL108213A$](/bulletins/10121927.md), 2017-11-03, Service bulletin: ENGINE AND ENGINE COOLING. NAG1 \(5A580\) Valve Body As per Warranty Bulletin D\-13\-22, please use R2108213A$ valve body for all Warranty \(W\), Mopar \(M\) and Mopar Vehicle Protection \(F\) claims.\~ Assembly also includes Filter \(52108325AA\) and Gasket \(52108332AA\).\~
- [2500108](/bulletins/10024083.md), 2008-03-06, Service bulletin: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE \(PCV\). POSITIVE CRANKCASE VENTILATION \(PCV\) SYSTEM FREEZES IN EXTREME COLD AMBIENT TEMPERATURES \-\- INVOLVES INSTALLING REVISED PCV SYSTEM COMPONENTS. \*NJ
- [1802707](/bulletins/10021686.md), 2007-06-15, Service bulletin: ENGINE AND ENGINE COOLING:ENGINE. MIL ILLUMINATION DUE TO EGR POSITION SENSOR DTC \- P0404, P0405, P0406. \*KB

JSON: [/v1/bulletins/10020194](/v1/bulletins/10020194)

[Report an error on this page](https://github.com/wenmar-pro/wenmar-open/issues/new?template=data_correction.yml&title=Data%20correction%3A%20Service%20bulletin%201802406&page=https%3A%2F%2Fopen.wenmarpro.com%2Fbulletins%2F10020194&vehicle=Service%20bulletin%201802406)