WenmarOpen by Wenmar Pro

Service bulletin 0505004

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10015817
Published by NHTSA2005-08-13
Manufacturer's number0505004
Manufacturer's date2005-05-01
NHTSA componentPOWER TRAIN

NHTSA's summary

SHIFT LOCK SOLENOID REMOVAL AND REPLACEMENT PROCEDURES. *TT 2002-2004 ISUZU AXIOM (UP), 198-2004 RODEO (UE) AND 1998-2004 RODEO SPORT. UPDATE *SC

The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

Components

Transmission and driveline

Vehicles listed
ISUZU AXIOM2002, 2003, 2004
ISUZU RODEO1998
ISUZU RODEO1999, 2000, 2001, 2002, 2003, 2004
ISUZU RODEO SPORT1998
ISUZU RODEO SPORT1999, 2000, 2001, 2002 (the catalog's model; the bulletin names a series or trim of it)

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
PIP3720D2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
0405S0012004-05-07. Service bulletin. SCS AUTOMATIC TRANSMISSION FLUID. *TT
0305S0012003-06-25. Service bulletin. TRANSMISSION INDICATOR LIGHT MAY BE ON AND DIAGNOSTIC TROUBLE CODE P1870 IS SET IN THE POWERTRAIN CONTROL MODULE (PCM). *TT
0205S0032003-04-01. Service bulletin. TRANSMISSION INDICATOR LIGHT MAY BE ON AND DIAGNOSTIC TROUBLE CODE P1870 IS SET IN THE PCM (POWERTRAIN CONTROL MODULE). *TT
0204S0032002-09-26. Service bulletin. REPLACEMENT ODOMETER PROGRAMING. *JG
SB0105S0012001-09-18. Service bulletin. SOME V6 MODELS WITH TRANSMISSION SERIAL NUMBERS 4754596 - 5831756 MAY EXPERIENCE LEAKAGE IN THE AREA OF OVERFILL PLUG AND OIL DRAIN PLUG. *TT
IB0105S0032001-09-18. Service bulletin. INFORMATION REGARDING THE OPERATION AND REPAIR OF THE TORQUE-ON-DEMAND (TOD) SYSTEM. *TT
IB0105S0022001-09-18. Service bulletin. SERVICE INFORMATION ON 4L FOUR-WHEEL DRIVE OPERATION. *TT
IB0004S0052001-01-28. Service bulletin. THIS BULLETIN PROVIDES INFORMATION ON THE P1640 AND P1650 OUTPUT DRIVE CODES WHICH REFER TO OUTPUT DRIVER CIRCUIT CONDITIONS RELATED TO THE PCM. *TT
SB0005S0022000-06-09. Service bulletin. CERTAIN VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSION (SERIAL NUMBER 5504006 - 5570892) MAY EXHIBIT THE MALFUNCTION INDICATOR LAMP ON AND TECH-II INDICATES THE PRESENCE OF TORQUE CONVERTER (DIAGNOSTIC TROUBLE CODE 1870) ON. *TT