Service bulletin 3396
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10013537 |
| Published by NHTSA | 2005-04-21 |
| Manufacturer's number | 3396 |
| NHTSA component | ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC) |
NHTSA's summary
SERVICE STABILITY MESSAGE DISPLAYED IN THE DIC. DIAGNOSTIC TROUBLE CODES C0290, C0292, C0131, OR C0196 SET IN THE EBCM. *TT
The document
No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.
Components
Driver assistance
Trouble codes named
C0131, C0196, C0290, C0292
| CADILLAC ESCALADE | 2004, 2005 |
|---|---|
| CHEVROLET AVALANCHE | 2004, 2005 |
| CHEVROLET SUBURBAN | 2004, 2005 |
| CHEVROLET TAHOE | 2004, 2005 |
| GMC YUKON | 2004, 2005 |
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 10-00-89-006C | 2018-04-16. Service bulletin. This informational bulletin provides directions on submitting different PIRs |
|---|---|
| PIP5168F | 2018-02-21. Service bulletin. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. |
| PIT4954C | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that have a Service Suspension System message on the Driver Information Center and the rear suspension ride height is incorrect. Technician will find Diagnostic Trouble Code C0696 or C0711 set in Electronic Suspension Control. Technician will need to inspect air compressor assembly for wire damage and repair any damage do not replace the complete air compressor assembly. Some vehicles may have a Service Suspension System message on the Driver Information Center and may also comment that the rear suspension ride height may be low under a heavy payload. Technician will follow published Service Information diagnostics and if determine if the sensor needs to be replaced technician will need to replace a complete air filter, dryer, and sensor assembly. Some vehicles may have a loose hose hanging down in the left rear of the vehicle. Technician will replace the auto leveling compressor air inlet filter and hose assembly. Also some vehicles may have automatic level control compressor is no longer performing a self-test at start up. Be advised the automatic level system normally will not or very infrequently cycle the compressor at key up. |
| 3013 | 2004-08-23. Service bulletin. UNWANTED STABILITRAK ACTIVATION OR STABILITRAK DISABLE MESSAGE APPEARS ON THE DIC. *TT |